Home

Home

Synthetics Cutting & Grinding Fluids

A true solution synthetic fluid will be clear with a particle size of less than 0.000001mm (0.00000004"). It will be an excellent coolant but will have no lubricity. It will typically have hard water tolerance.

A surface active synthetic fluid will be translucent to clear. It will contain wetting agents, which lower the surface tension of the fluid and enhance the lubricity. It will have good rust inhibiting properties, and although it will have a tendency to foam, this should not present a major concern.

Number of products in category is 6

TRIM® 9106

Synthetic

TRIM<sup>®</sup> 9106

TRIM® 9106 is a clear, virtually odorless, synthetic coolant with excellent heat dissipating and corrosion inhibiting qualities. 9106 is recommended for grinding operations on cast iron, aluminum and steels. 9106 will not form ammonia when grinding cast iron. 9106 allows graphite to float, and prevents swarf from clinkering when grinding cast iron. 9106 contains no sulfur, phosphorus, chlorine or other halogens.

  • Very operator, machine and environmentally friendly
  • Moderate pH
  • Contains no biocides, no oil, and no halogens
  • Will not form ammonia or other gases when grinding or machining cast iron
  • Inhibits chip packing and clinkering
  • Operators like 9106’s very low odor, low foam, low mist, and water clear working solution
  • Compatible with brass, aluminum, and lead serrations on magnetic grinding chucks
  • Machines are easily washed off with coolant working solution to minimize the buildup of residues and chips
  • Very low carryoff for extremely low fluid operating costs
  • Easy recycling or disposal with conventional techniques and equipment

TRIM® C115

Synthetic

TRIM<sup>®</sup> C115

TRIM® C115 is a high-performance synthetic fluid for working cast iron and mild steels. State-of-the-art chemical technology provides excellent cooling and chip settling, good tramp oil rejection, and machine cleanliness while leaving a protective film on the machine tool.

  • Compatible with a very wide range of materials including cast iron, steels, plastics, and composites
  • Does an excellent job in most glass, ceramic, and composite grinding applications
  • Excellent corrosion inhibition on most common ferrous and nonferrous alloys
  • Extremely low carryoff keeps operating costs down
  • Low foam and mist
  • Very low initial odor level which usually disappears after one to two days
  • Keeps your machines clean while leaving a soft, fluid film that protects bare metal parts
  • Exceptional sump life and very good tramp oil rejection

TRIM® C270

High-performance Synthetic

TRIM<sup>®</sup> C270

TRIM® C270 is a state-of-the-art synthetic coolant. C270 provides excellent cooling and chip settling, good tramp oil rejection, and machine cleanliness, and meets the need of the modern job shop for a single premium synthetic coolant for virtually all machining operations.

  • C270 is compatible with a very wide range of materials including: cast iron, steels, and copper alloys, as well as plastics and composites
  • Provides excellent corrosion inhibition on all common ferrous alloys
  • Does a great job in form grinding, drilling, tapping, and reaming operations without chlorine or sulfur based EP additives
  • Extremely low carryoff for very low total operation costs
  • Very low foam and mist
  • Keeps your machines clean while leaving a soft, fluid film that protects the bare metal parts. This residual film is easily resoluble in coolant working solution to facilitate easy machine cleaning and minimize the buildup of sticky residues that can hold machine-destroying chips
  • Exceptional sump life and very good tramp oil rejection
  • A very low initial odor level which usually disappears after one-to-two days

TRIM® C270CG

High-performance Synthetic

TRIM<sup>®</sup> C270CG

TRIM® C270CG is a state-of-the-art synthetic coolant. C270CG provides excellent cooling and chip settling, good tramp oil rejection and machine cleanliness and meets the need of the modern job shop for a single premium synthetic coolant for virtually all machining operations.

  • C270CG is compatible with a very wide range of materials including: cast iron, steels, and copper alloys, as well as plastics and composites
  • Provides excellent corrosion inhibition on all common ferrous alloys
  • Does a great job in form grinding, drilling, tapping, and reaming operations without chlorine or sulfur-based EP additives
  • Extremely low carryoff for very low total operation costs
  • Very low foam and mist
  • Keeps your machines clean while leaving a soft, fluid film that protects the bare metal parts. This residual film is easily resoluble in coolant working solution to facilitate easy machine cleaning and minimize the buildup of sticky residues that can hold machine-destroying chips
  • Exceptional sump life and very good tramp oil rejection
  • A very low initial odor which usually disappears after one to two days

TRIM® C320

High-lubricity Synthetic

TRIM<sup>®</sup> C320

TRIM® C320 is a high lubricity, low foam, synthetic coolant that approaches the "down-the-hole" machining performance of premium soluble oils. This product is exceptionally good on aluminum. Even with its very high performance, C320 meets or exceeds most stringent environmental standards.

  • Excellent extreme pressure (EP) lubricity to do many drilling, tapping, reaming, and form-grinding operations without any chlorine or sulfur-based EP additives
  • A very versatile product which works well in mixed metal situations including aluminum, steel alloy, cast iron, and copper alloy
  • Provides good corrosion inhibition on all common ferrous and nonferrous alloys
  • Keeps grinding wheels clean and sharp for higher “G ratios”, better surface integrity, and faster stock removal
  • Contains no DEA, nitrides, phenolic compounds, “formaldehyde releasers”, or chlorine
  • Operators like C320’s very low odor, low foam, low mist, and pale-yellow working solution
  • Keeps your machines clean while leaving a soft fluid film that protects the bare metal parts
  • Machines are easily washed off with coolant working solution to minimize the buildup of residues and chips
  • Exceptional sump life, great resistance to fungus and bacteria, and good tramp oil rejection
  • C320 is a super product for aluminum wheel machining

TRIM® CLEAR

Corrosion-inhibiting Synthetic

TRIM® CLEAR is a synthetic cutting and grinding fluid concentrate. It works best where high-heat removal and low- working concentrations are critical. CLEAR is particularly suited for surface grinding and similar operations requiring maximum heat transfer. It is often used effectively in double disc grinders, belt grinding, and abrasive cutoff operations on ferrous materials.

  • CLEAR contains no sulfur, phosphorus, or chlorine
  • Will not form ammonia or other gases when grinding or machining cast iron
  • Settles chips and swarf rapidly and lends itself to very high flow rates in positive media filtration
  • Low mist and odor
  • Very low foam even at very high pressures and flow rates
  • Coolant residue is easily cleaned up with either water or working solution
  • Very low carryoff for extremely low fluid operating costs
  • Rejects tramp oil for easy skimming and recycling
  • Easy recycling or disposal with conventional techniques and equipment