Solutions Products Support About Us Find a Distributor Contact Us
Solutions Products Support About Us
Solutions Products Support

New Products

TRIM™ TC 108

Metalworking Fluid Defoamer

TRIM TC 108 is a highly effective tank side additive used to control foam in metalworking fluid systems.

  • Paintable
  • Plateable

TRIM™ TC 109

Silicone Free, Tank Side Defoamer

TRIM TC 109 is a silicone free antifoam or defoamer. It is used as a tank-side additive to control foam in water-miscible coolants, washing compounds, floor soaps, etc.

  • Antifoam
  • Silicone free

Yellow Bellied Sump Sucker™ Li'l Sucker™

Yellow Bellied Sump Sucker™ Li'l Sucker™

The Li'l Sucker™ is the newest addition to the Yellow Bellied Sump Sucker™ line of sump cleaning vacuums. Based on extensive customer research and extended field trial experience, customers were able to tell us what they liked, disliked, felt had no value, and would change in the previous designs. The result was the Yellow Bellied Sump Sucker that customers designed. It is durable, highly maneuverable, easy to use, and provides exceptional suction and discharge flow rates.

  • Removes the coolant, sludge, and chips from the sump
  • Filters the sludge and chips from the fluid
  • Returns filtered coolant to the machine tool sump, or
  • Transports the coolant to waste treatment for disposal, or to a XYBEX Recycling System for recycling

Features

  • Tank capacity of 50 gallons (190 liters)
  • Suction rate up to 85 GPM (320 LPM)
  • Discharge rate up to 40 GPM (150 LPM)
  • 1.6 ft3 (45 dm3) chip basket holding capacity, roughly 12 gallons (45 liters)
  • Available in both air venturi and electric models
  • 120 VAC, single phase, 50 Hz/60 Hz electric model standard
  • 220 VAC, single phase, 50 Hz/60 Hz electric model optional
  • Complete with hoses and straight cleaning tool
  • Optional cleaning tools available
  • Perfect for today's smaller machine tool sumps

    TRIM™ OM 360

    Straight Cutting Oil

    TRIM OM 360 is a high quality mineral oil containing an effective synthetical ester additive. It is designed for cutting and grinding a wide range of materials, and especially for steel broaching. This product can also be used for tapping, gear milling, or reaming. It is also suitable for aluminum alloy machining and steel heat treatment.

    • Excellent EP lubricating performance, good built up edge control (B.U.E.), provides super surface finish
    • Provides outstanding lubricating and cooling necessary for deep hole machining
    • Low mist and volatilization, keep working environment clean

    TRIM™ E935

    Premium Universal Emulsion

    TRIM E935 is a premium universal emulsion for use on a broad range of ferrous and nonferrous metals, effective in most cutting and grinding operations. The stable and predictable performance of E935 makes it a first choice for precision and consistent parts manufacturing.

    • Very wide application range
    • Good hard water tolerance
    • Keeps machine tools clean
    • Works very well in general machining
    • Very stable formula provides good operational life with consistent performance
    • High tramp oil resistance for easy oil removal and longer coolant life
    • Easily recycled or disposed of using conventional techniques and equipment
    • Good balance of cooling and lubrication providing good tool life and surface finishes
    • Leaves a very light, oily, non-gumming residue to prevent sticky ways, chucks, tool holders, and fixtures
    • Extremely stable fine particle size emulsion allows for reduced carry-off and super-high penetrability to get the fluid to the point of cut

    TRIM™ DRIVE CF3

    High-performance Fluid for Hard Disk Drives

    TRIM DRIVE CF3 is a specialized, chlorine-free, heavy-duty coolant formulated to meet the high-precision machining and stringent chemical restrictions of the Hard Disk Drive (HDD) industry. It has very good wetting and great lubricity resulting in excellent surface finishes and its ease of wash-ability makes DRIVE CF3 an excellent choice for HDD components manufacturers. TRIM DRIVE CF3 will run in high-pressure situations with little to no foam.

    • In addition to aluminum alloy, it is also suitable for a wide range of materials including steels and stainless steels
    • Low foam even in high-pressure operations without the use of silicone antifoam
    • Good hydrodynamic lubrication to perform reaming and threading applications
    • Excellent anti-weld properties without the use of either chlorinated or sulfurized EP additives
    • Keeps machines very clean while leaving a fluid, oily residue for ease of cleaning and reduced machine maintenance costs
    • Does not require special disposal and is easily recycled
    • Non-staining on aluminum alloys commonly used to produce HDD components
    • After machining, parts can be washed easily and completely in aqueous washing systems

    TRIM™ OGM100HF

    High Flash Point Gear Grinding Oil

    TRIM OGM100HF is a high-efficiency grinding oil composed of high-quality mineral oil and various high-quality oil additives. This product has good permeability and lubricity, and can be used in the grinding process of materials (especially gear grinding) like cast iron, alloy steel, stainless steel, etc. It is also suitable for various profile grinding, internal and external grinding, cutting, centerless grinding, and other grinding processes.

    • Does not contain phosphorus or heavy metals, which protects the environment and reduces pollution
    • Light color, low odor
    • Good material compatibility
    • Safe and non-irritating to the skin
    • Produces good surface finishes
    • Provides high-strength lubricity in various medium-to-heavy-duty machining operations
    • Meets the cutting requirements of various machining operations: such as, automatic lathes, special machines, CNC lathes, and machining centers.

    TRIM™ E206KS

    Long-life Emulsion

    TRIM E206KS is a high quality universal emulsion coolant concentrate. It has been designed for a very broad range of metals allowing its effective use in most cutting and grinding operations, which requires minimal maintenance even in the most demanding fluid management systems. It has the lubricity and "guts" necessary to do heavy-duty machining. The stable and predictable performance of TRIM E206KS makes it a first choice for high-quality, consistent parts manufacturing.

    • Very stable formula provides long operational life with consistent performance
    • Has a very wide application range allowing its effective use on cutting and grinding
    • Extremely hard water tolerance
    • Extremely stable fine particle size emulsion to reduce carry-off and super-high penetrability to get the fluid to the point of cut
    • Provides good tool life and surface finishes
    • High tramp oil resistance for easy oil remove, longer coolant life and more opportunities to be recycled
    • Leaves a very light oily, non-gumming residue to prevent sticky ways, chucks, tool holders and fixtures
    • Coolant residue is easily removed with either water, working solution or aqueous cleaners
    • Good cleaning performance keeps machine tool very clean
    • Easy recycling or disposal with conventional techniques and equipment
    • Run effectively for long periods without the need for costly additives

    TRIM™ E712

    Low Maintenance, General Purpose Emulsion

    TRIM™ E712 is high quality universal soluble oil which requires minimal maintenance in even the most demanding fluid management systems. It has broad application in machining and grinding on a wide range of materials. The high levels of both chemical and mechanical lubricity in this product handle the tough machining and grinding jobs. It leaves a very easy to clean protection film on the work piece and machine parts to prevent corrosion on metal surface including the machine tool. The stable and predictable performance of TRIM E712 makes it a first choice for high-quality, consistent parts manufacturing.

    • Very stable formula provides long operational life with consistent performance
    • Extremely hard water tolerant
    • Very wide application range. Suitable for both grinding and machining
    • Fine particle size emulsion reduces carry-off and facilitates getting the fluid to the point of cut
    • In high-speed turning and milling, provides good tool life and surface finishes
    • Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders and fixtures
    • Coolant is easily removed with water, working solution or aqueous cleaners
    • Easy recycling or disposal with conventional techniques and equipment
    • Will run effectively for long periods without the need for costly additives. Easily recyclable and/or dispose with conventional recycling and/or disposal techniques

    TRIM™ MicroSol™ 692XT

    Premium, High-lubricity, Low-foam Microemulsion

    TRIM™ MicroSol™ 692XT

    TRIM MicroSol 692XT is a high-lubricity, semisynthetic, microemulsion coolant. This formula delivers extended sump life, greater bio stability, and better foam control versus previous generation semisynthetic Microemulsions. It does very well in mixed metal situations and is compatible with a very wide range of materials including titanium, high nickel alloys, steels, copper, and aluminum alloys. Improved tramp oil rejection keeps your production running smoothly. Increase your profitability and production with TRIM MicroSol 692XT!

    • Improved lubricity for longer tool life
    • Dramatically extends useful life without the need for tank-side biocides or fungicides
    • Halogen free
    • Low foaming for todays demanding high-pressure, high-volume applications
    • Excellent alternative to chlorinated soluble oils on high-silica aluminum alloys
    • Provides superior corrosion inhibition on all ferrous and nonferrous metals
    • Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance
    • Requires no special disposal or recycling techniques

    TRIM™ OM 210

    High-performance, Cutting and Grinding Oil

    TRIM OM 210 is a low-odor, light-colored oil designed for operations where low viscosity and high lubricity are required. In addition to general machining, OM 210 is particularly effective in deep-hole drilling and creepfeed grinding where its ability to flow into the cutting zone and "wet" the surfaces increases tool life and reduces heat.

    • Light color and low odor
    • High flash point
    • Minimal carry over loss
    • Excellent chips flushing and low foam
    • Oxidation inhibited for longer life
    • Excellent tool life properties

    TRIM™ OM 303

    Nonchlorinated Cutting and Lubricating Oil

    TRIM™ OM 303

    TRIM OM 303 is a highly formulated straight oil designed for use in conventional and Swiss style screw machines, high-speed turning centers, and high-performance, multi-station machines, such as Hydromats. OM 303 is safe for use on aluminum alloy and steel alloy parts, as well as cast iron, copper, brass, and bronze. This product is excellent for high-pressure applications such as thread rolling and thread-form tapping. OM 303 has proven itself in difficult operations on stainless and bearing steels. OM 303 provides lubrication properties similar to ISO 32 general-purpose lube oils.

    • Very light colored and clean running
    • Low foaming and low misting for use in aggressive operations
    • Oxidation inhibited for longer life, and an excellent choice where both ferrous and aluminum or copper alloy parts are being machined aggressively
    • Far easier to wash off parts than many oils of similar or even lower performance
    • Has replaced dark, active sulfur/chlorine straight oils in several large operations while providing superior results in tool life
    • An outstanding product in thread rolling, thread form tapping, and in Swiss screw machines with solid bushings
    • Contains no active sulfur; therefore, does not stain parts

    TRIM™ C290

    Economical Synthetic Fluid for Aluminum Machining

    TRIM C290 is a synthetic metalworking fluid optimized for the chemical, environmental, and machining requirements of general aluminum parts. C290 is a high performance, easy to use and maintain, metal removal fluid with very high levels of usable lubricity at the point-of-cut. C290's unique chemical formula allows great, nonferrous corrosion prevention on most aluminum alloys.

    • Great resistance to corrosion on nonferrous materials including aerospace aluminums 6061, 7075, 2024, 3000
    • Water-clear, low-foaming and -misting, C290 is a joy to work with and manage
    • Provides good results in a wide range of grinding and machining operations
    • Excellent tramp oil rejection
    • Easily removed from parts for easy cleanup before assembly, painting, or plating operations
    • PRTR compliant, no SARA 313 reportable chemistry. Product contains no chlorine, phenol, nitrites, copper, triazine, or silicone
    • Very low carryoff and long sump life results in low operating cost

    TRIM™ MicroSol™ 687NXT

    Premium High-lube PRTR Microemulsion

    TRIM MicroSol 687NXT is a translucent, premium high-lube, PRTR compliant microemulsion. The product is low foaming in soft water but is also stable in hard water. The product is designed to machine difficult to machine metals, such as stainless steel and Inconel. It is also good for most aluminum alloys including aerospace grade.

    • Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance
    • Excellent compatibility with a very wide range of material including stainless steel, nickel alloys, titanium, and aluminum alloys
    • Greatly extends useful life without the need for tank side biocides or fungicides
    • Low foaming for modern high-pressure, high-volume applications
    • Uses standard metalworking recycling and disposal techniques
    • Does not contain any chemical listed under Japan PRTR regulation
    • Provides superior corrosion inhibition on all ferrous metals

    XYBEX™ ChipOut™

    Chip & Sludge Remover

    XYBEX™ ChipOut™

    A perfect match-up with the PurifierPlus is the XYBEX ChipOut. It is also a compact, easy-to-use, affordable solution for optimizing production. It simply and effectively sucks out the coolant, chips, and swarf to collect and filter all solid impurities and return clean coolant to the tank.

    Get the most from your coolant with ChipOut. It literally pays for itself in no time with significant cost savings.

      XYBEX ChipOut
      • Separates surface debris, bottom chips and swarf, and sediment from coolant
      • Extends coolant life
      • Improves surface finish on parts
      • Reduces maintenance
      • Uses diaphram pump air pressure, no electricity required
      • High suction power, flow rate of 180 liters/min
      • Runs during production without shutting off machine tools
      • Adjustable stainless steel filters: standard mesh 380 microns; optional: 830 microns and 180 microns
      • Optional floating device for maximum tramp oil collection
      • Portable and easy to use with multiple machines
      • Operates with water-soluble coolants or neet oils
      Cost effective ChipOut adds up to big savings
      • Reduces annual coolant cost
      • Reduces expensive parts rejects
      • Reduces maintenance to a minimum

    XYBEX™ ChipOut Plus™

    Magnetic Centrifugal Sludge & Chip Remover

    XYBEX™ ChipOut Plus™

    Looking for a fast, affordable way to have longer coolant life, reduce maintenance, and achieve better machinability and surface finish? Hardworking ChipOut Plus delivers all that and more in a compact, portable system that can hook up to machines throughout the shop.

    It does double time, as both a centrifugal and magnetic separator for water-based cutting fluids or neat oils. It’s simple to use, powerful, and efficient.

    First, the suction hose draws in the liquid and impurities. The filtration bucket traps large impurities before the sludge-containing fluid enters the centrifugal separator where fine particles are separated out by centrifugal force. The sludge then enters the powerful magnetic separator which efficiently removes magnetic metallic shavings and particles. Just like its name implies, it takes out chips - plus more!

      XYBEX ChipOut Plus
      • Separates surface debris, magnetic dust and shavings, chips, swarf, and sediment from coolant
      • Extends coolant life
      • Improves surface finish on parts
      • Reduces maintenance
      • Separates using centrifugal and magnetic force
      • Provides extremely fine filtration
      • No need to stop the machine
      • Quick filtration, easy to operate
      • Portable, use with multiple machines
      • No consumables needed
      Use hardworking, cost effective ChipOut Plus to reduce costs and build profits
      Save time and build up profits with ChipOut Plus.
      • Reduces annual coolant cost
      • Reduces maintenance and manpower
      • Reduces costly parts rejects

    XYBEX™ PurifierPlus™

    Cutting Fluid Purifying System

    XYBEX™ PurifierPlus™

    The portable, cost-effective XYBEX PurifierPlus system pays for itself with material cost savings, reduced downtime and recycling costs. Not only does it enhance production and make the workplace cleaner, it also is better for employee health and the environment.

    Unlike units which simply separate machine tramp oil (the unwanted byproduct of the machining/metalworking process) from coolant, PurifierPlus has an ozone disinfection function which kills bacteria. Not only is the coolant cleaned and lasts longer, it’s purified and reused, and the subsequent problematic stench from bacteria and fungal growth is eliminated.

    Improve production, reduce costs, and experience a cleaner workplace with PurifierPlus.

      XYBEX PurifierPlus
      • Separates free tramp oil and extends coolant life
      • Reduces tool wear and costly parts rejects
      • Easy to use with a handy set-timer to operate on its own
      • Adjustable flow rate filter from 10 to 30 liters/hr
      • Kills bacteria (for best results run 1 hour for each 100 liters in sump; ozone function disinfects at 500 mg/hr)
      • Built-in pH detector (optional) adjusts pH to control range
      • Portable for use on multiple machines in the facility
      PurifierPlus quickly pays for itself in savings
      • Saves 10% to 25% on annual coolant cost
      • Saves 30% to 50% on additional water cost
      • Saves 10% to 25% on tooling costs and part reworks
      • Reduces clean-up time 60% to 80% annually

    TRIM™ E950

    High Performance Machining Emulsion

    TRIM E950 is a proprietary blend of new vegetable-based technology and premium traditional lubricity additives to yield a very high performance, low management metal removal fluid. This premium emulsion product is operator friendly because of its mild contact nature and low chemical initial-charge odour. TRIM E950 is robust enough to deliver extended useful life and avoid rancid odours normally associated with traditional emulsions. The unparalleled lubricity delivers exceptional surface finish and tool life on difficult to machine aluminium alloys, inconel, titanium, stainless and high tensile strength steels.

    • Delivers unparalleled lubricity
    • Very long sump life and low carry-off rates result in low operating cost
    • Low foam even in soft water areas
    • Hard water tolerant
    • Non-chlorinated and non-sulphurised extreme pressure (EP) additives control built-up edge (BUE) in tough operations on aerospace materials
    • Fine emulsion ensures fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior tool life and corrosion prevention
    • Compatible with all materials excluding magnesium
    • Easily recycled or disposed of without special handling or equipment
    • Will run effectively for long periods without the need for costly additives

    TRIM™ E860

    Low-foam, High-lubricity Emulsion

    TRIM E860 is a high-quality, general purpose emulsion for use on a broad range of ferrous and nonferrous metals, effective in most cutting and grinding operations. The stable and predictable performance of E860 makes it a first choice for precision and consistent parts manufacturing.

    • Very wide application range
    • Good hard water tolerance
    • Keeps machine tools clean
    • Works very well in general machining
    • Very stable formula provides good operational life with consistent performance
    • High tramp oil resistance for easy oil removal and longer coolant life
    • Easily recycled or disposed of using conventional techniques and equipment
    • Good balance of cooling and lubrication providing good tool life and surface finishes
    • Leaves a very light, oily, non-gumming residue to prevent sticky ways, chucks, tool holders, and fixtures
    • Extremely stable fine particle size emulsion allows for reduced carry-off and super-high penetrability to get the fluid to the point of cut

    WEDOLiT FN 6160-90

    High performance forming oil

    WEDOLiT FN 6160-90 is a water-insoluble, chlorinated lubricant for deep drawing and other cold forming operations, e.g. wire drawing, extrusion, or thread forming of steel and stainless steel. The undiluted product is usually applied by flooding, spraying, brushes, or by means of rollers.

    • Stable load carrying capacity and a homogenous sliding behavior
    • Reduces friction and wear and thus contributes to a high tool life
    • Outstanding wetting ability and film formation without adhesion
    • Stable cold start behavior, prevents stick-slip and chatter
    • Leads to clean surfaces and contributes to achieve dimensional accuracy
    • Easily removable with organic solvents or alkaline industrial cleaners

    WEDOLiT FN 8830

    Special forming oil

    WEDOLiT FN 8830 is a chlorine free, pasty, water-insoluble lubricant for cold forming processes (e.g. pilgering) of high alloyed steels. The product is usually applied on the outer diameter by brushes or by means of rollers.

    • Stable load carrying capacity and a homogenous sliding behavior
    • Reduces friction and wear and thus contributes to a high tool life
    • The outstanding extreme-pressure properties combined with an exceptional adhesion offers the possibility for high degrees of deformation
    • Stable cold start behavior, prevents stick-slip and chatter
    • Contributes to achieving dimensional accuracy
    • Pigments will remain on the surface after annealing and need to be removed (e.g. by pickling with HCl or HNO3) before further processing

    WEDOLiT CS 8208

    Water-miscible, fully synthetic coolant

    WEDOLiT CS 8208 is suitable for ultrasonic testing systems. The product is also suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 5 - 10%). Not suitable for the manufacturing of workpieces made of zinc, aluminum and their alloys.

    • Offers high cooling- and flushing properties with a very good wetting behavior
    • Contributes to a high tool life
    • Very good application stability
    • Almost free of foam
    • Offers a good skin compatibility
    • Due to its thermal stability, the product can be used in almost the whole process chain of welded tubes (forming, welding, calibration, sawing)

    WEDOLiT FN 1190-2300

    High-performance forming oil

    WEDOLiT FN 1190-2300 is a highly viscous, chlorine containing forming oil for tube drawing and other cold forming operations of stainless steel. The undiluted product is usually applied by brushes or by means of rollers.

    • Stable load carrying capacity and a homogenous sliding behavior
    • Reduces friction and wear and thus contributes to a high tool life
    • Outstanding wetting ability and film formation without adhesion
    • Stable cold start behavior, prevents stick-slip and chatter
    • Leads to clean surfaces and contributes to achieving dimensional accuracy
    • Easily removable with organic solvents or alkaline industrial cleaners
    • Soluble in chlorinated hydrocarbons

    WEDOLiT FN 1571-2800

    Drawing Brass and Copper Tubes

    WEDOLiT FN 1571-2800 is a highly viscous, water-insoluble lubricant for tube drawing and other cold forming processes of aluminum and non-ferrous metals. The undiluted product is usually applied by brushes or by means of rollers.

    • Stable load carrying capacity and a homogenous sliding behavior
    • Reduces friction and wear and thus contributes to a high tool life
    • Outstanding wetting ability and film formation without adhesion
    • Stable cold start behavior, prevents stick-slip and chatter
    • Leads to clean surfaces and contributes to achieve dimensional accuracy
    • Easily removable with organic solvents or alkaline industrial cleaners
    • Evaporates at temperatures T ≥ 572°F, (300°C) without leaving any residues or stains on the metal surface. Therefore, no preliminary degreasing is necessary before a potential soft annealing

    WEDOLiT FN 8850-90

    Drawing small diameter tubes, diesel injection

    WEDOLiT FN 8850-90 is a medium viscous, water-insoluble lubricant for tube drawing and other cold forming operations of steel. Due to the fact that the product also offers corrosion protection, no additional treatment is necessary (for short term storage). The undiluted product is usually applied by spraying, brushes, or by means of rollers.

    • Stable load carrying capacity and a homogenous sliding behavior
    • Reduces friction and wear and thus contributes to a high tool life
    • Outstanding wetting ability and film formation without adhesion
    • Stable cold start behavior, prevents stick-slip and chatter
    • Leads to clean surfaces and contributes to achieving dimensional accuracy
    • Easily removable with organic solvents or alkaline industrial cleaners

    WEDOLiT FS 4710

    Solvent base for aluminum stamping 158°F (70°C)

    WEDOLiT FS 4710 is a low viscous, solvent-based lubricant for stamping and forming operations of steel, aluminum and non-ferrous metals. The undiluted product is usually applied by spraying, flooding, brushes, or by means of rollers.

    • Good spreading behavior, which leads to a uniform wetting of the metal surface
    • Stable load carrying capacity and a homogenous sliding behavior
    • Reduces friction and wear and thus contributes to a high tool life
    • Leads to clean surfaces and contributes to achieving dimensional accuracy
    • If the product is finely dispersed, it evaporates after a short time without leaving any residue. Therefore, an additional cleaning step is not necessary. Otherwise, it is easily removable with organic solvents or alkaline industrial cleaners

    WEDOLiT FW 1960

    Soap for tube drawing operations

    WEDOLiT FW 1960 is a water-soluble alkaline soap for heavy drawing operations of steel tubes. The product is usually used as an immersion bath (bath temperature 167 - 194 °F, (75 – 90 °C)).

    • The product is designed to react with the zinc phosphate layer (which acts as lubricant) to form a zinc soap. The zinc phosphate layer should be at least 4 μm (at heavy forming operations, e.g. cold extrusion, up to 10 μm). Due to specific additives, a maximum conversion of zinc phosphate and the drawing media occurs, which results in an optimal performance regarding degree and rate of deformation
    • Can be used in very low concentrations of 5 - 10% as an aqueous solution (tube drawing). The best results are obtained with water free media
    • Offers (in combination with a zinc phosphate layer) very high cross-sectional reduction and high drawing velocities – up to 100 m/min (steel tubes with standard cross-sectional reduction)