Solutions Products Support About Us Find a Distributor Contact Us
Solutions Products Support About Us
Solutions Products Support

WEDOLiT AE 1030

High-Performance-Ester-Fluid

WEDOLiT AE 1030 is a dewatering fluid based on the latest ester technology that uses surface-active substances to displace both water and emulsions from the metal surface quickly. Even highly complex geometries can be efficiently dewatered. It is mainly used as an immersion bath at room temperature.

Not subject to the German solvent guideline VOC 31. BImSCHV or to the Swiss regulation concerning the incentive tax on volatile solvents (VOCV). Fulfils all requirements regarding ELV 2000/53/EG.

  • Due to its strong dewatering effect, residues of flushing water or water containing fluids such as emulsions or synthetic coolants are removed from the metal surface
  • Water/emulsions that enter the bath will settle on the bottom of the tank after a short period and can be drained off
  • Development of a clear phase boundary between the water and the product, without forming an emulsion phase
  • Excellent bath-life
  • Additive loss due to water contact: None

WEDOLiT AE 4313

High-Performance-Ester-Fluid

WEDOLiT AE 4313 is a modern formulated, ester-based corrosion inhibitor for steel and other metals, which offers protection for short overseas transports. It can be applied by spraying, flooding or by means of rollers.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Suitable for short overseas transport
  • No negative labelling
  • Suitable for VCI-foils
  • Stable against acidic and alkaline contamination
  • Excellent material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

WEDOLiT AN 6111

High-Protection-DW-Fluid 100°C flash point
(aromatic content ≤ 2%)

WEDOLiT AN 6111 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Ideal compatibility with VCI-foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Low

WEDOLiT AN 6999

High-Protection-Fluid 170°C flash point (aromatic content ≤ 2%)

WEDOLiT AN 6999 is a modern formulated corrosion inhibitor for steel and other metals. It offers long-term corrosion protection (indoor storage and potentially outdoor storage) and can be applied by brushes or by means of rollers.

  • Ideal for overseas transport
  • Suitable for VCI-foils
  • Good protection for outdoor storage
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Ideal for covered storage
  • Offers protection against atmospheric contamination, e.g. dissolved gases that cannot penetrate the protecting film (water vapour permeability)

WEDOLiT AN 7114

High-Protection-DW-Fluid 120°C flash point

WEDOLiT AN-7114 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

WEDOLiT AN-7114 fulfills all requirements regarding Altautorichtlinie 2000/53/EG. It is not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Ideal compatibility with VCI-foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Low

WEDOLiT AN 7121

Lanolin-Protection-Fluid 100°C flash point
(aromatic content ≤ 2%)

WEDOLiT AN 7121 is a modern formulated corrosion inhibitor for steel and other metals, which develops a slightly greasy film. The resulting film consists of natural corrosion protection additives with a specific odour. It offers a long-term corrosion protection (indoor storage) and can be applied by spraying, flooding or rolling. Homogenisation before usage is recommended.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) or to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Ideal for VCI-foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Ideal for covered storage
  • Offers protection against atmospheric contamination, e.g. dissolved gases which cannot penetrate the protecting film (water vapour permeability)

WEDOLiT AN 7210

High-Protection-DW-Fluid 130°C flash point
(aromatic content ≤2%)

WEDOLiT AN 7210 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Suitable for overseas transport
  • Ideal compatibility with VCI-foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Low

WEDOLiT AN 9921-100

Medium term RP 100°C flash point,

WEDOLiT AN 9921-100 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow bodies. It can also be applied by spraying, flooding or by means of rollers. Due to the high oil content, it can also be used as a straightening oil.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) or to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Can be used as a straightening oil or for light forming processes after the solvent has evaporated
  • Stable against acidic and alkaline contamination
  • Excellent bath life
  • Excellent material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Extremely low

WEDOLiT AS 1012

Dewatering-fluid 40°C flash point

WEDOLiT AS 1012 is a dewatering fluid with corrosion protection properties. It uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can efficiently be dewatered. It is mainly used as an immersion bath at room temperature.

  • Due to its strong dewatering effect, residues of flushing water or water containing fluids including emulsions or synthetic coolants are removed from the metal surface
  • After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage
  • Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off
  • Development of a clear phase boundary between the water and the product, without forming an emulsion phase
  • Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
  • Excellent bath-life
  • Additive loss due to water contact: None

WEDOLiT AS 1211 (K 722)

Dewatering-fluid 40°C flashpoint
(aromatic content ≥ 2%)

WEDOLiT AS 1211 is a dewatering fluid with a corrosion protection that uses surface-active substances to displace both water and emulsions from the metal surface extremely quickly. Even highly complex geometries can be quickly and efficiently dewatered. It is mainly used as an immersion bath at room temperature.

The product is approved by Mercedes-Benz Group AG (formerly Daimler AG) (QSO 040212) under the name K 722.

  • Due to its strong dewatering effect, residues of flushing water or water containing fluids such as emulsions or synthetic coolants are removed from the metal surface
  • After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage
  • Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off
  • Development of a clear phase boundary between the water and the product, without forming an emulsion phase
  • Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
  • Excellent bath-life
  • Additive loss due to water contact: None

WEDOLiT AS 1723

High-Protection-Wax-dispersion-Fluid 30°C flash point

WEDOLIiT AS 1723 is a universal, solvent-containing, long-term corrosion protection. It contains a newly formulated thixotropic wax dispersion, which allows a long period of protection under covered storage as well as a limited period of outdoor storage. It can be applied by spraying, flooding, brushing or by means of rollers.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • After the evaporation of the solvent (quick drying time), a waxy, light-coloured, non-adhesive and non-dust-binding, age-resistant protective film is formed on the treated surface
  • Good protection for outdoor storage
  • It´s recommended to homogenise the product before use or after a longer storage period
  • Protection against atmospheric contaminations such as dissolved gases that cannot penetrate the protective film (water vapour permeability)

WEDOLiT AS 2111

Universal RP 40°C flash point

WEDOiT AS 2111 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Extremely low

WEDOLiT AS 2111-CM

Protection-DW-Fluid 40°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS 2111-CM is a modern formulated corrosion inhibitor for steel and other metals, that offers protection for short overseas transport. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

  • Suitable for overseas transport
  • VCI films suitable: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed, especially before packing in boxes with film
  • Stable against acidic and alkaline impurities
  • Good material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Water displacing with very good wetting behaviour
  • Additive loss due to water contact: Extremely low

WEDOLiT AS 2241

High-Protection-DW-Fluid 40°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS-2241 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Extremely low

WEDOLiT AS 2251

Long term DW Fluid 40°C flash point

WEDOLiT AS-2251 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Very low

WEDOLiT AS 2603

High-Protection-Waxdispersion-Fluid 40°C flash point

WEDOLiT AS 2603 is a universal, solvent-containing, long-term corrosion protection. It contains a newly formulated thixotropic wax dispersion, which allows a long period of protection under covered storage as well as a limited storage period for outdoor storage. It can be applied by spraying, flooding, brushing or rolling.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • After the evaporation of the solvent (quick drying time), a waxy, light-coloured, non-adhesive and non-dust-binding, age-resistant protective film is formed on the treated surface
  • Good protection for outdoor storage
  • It´s recommended to homogenise the product before use or after a longer storage period
  • Protection against atmospheric contaminations such as dissolved gases that cannot penetrate the protective film (water vapour permeability)

WEDOLiT AS 3040

Dewatering-fluid 60°C flash point

WEDOLiT AS 3040 is a dewatering fluid with corrosion protection properties that uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can be efficiently dewatered. It is mainly used as an immersion bath at room temperature.

  • Due to its strong dewatering effect, residues of flushing water or water containing fluids including emulsions and synthetic coolants are removed from the metal surface
  • After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage
  • Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off
  • Development of a clear phase boundary between the water and the product, without forming an emulsion phase
  • Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
  • Excellent bath-life
  • Additive loss due to water contact: None

WEDOLiT AS 4111

Special-Fluid 60°C flash point

WEDOLiT AS 4111 is a leading edge universally applicable, corrosion protection which offers a long-term protection for indoor storage. It has been especially developed for loosening rusted parts and can be applied by spraying, flooding or via an immersion bath.

  • Suitable for overseas tranpsort
  • Rust remover for humidity-related ignition problems in electrical systems
  • Loosens rusted screws, nuts, joints, hinges, switches and mechanisms
  • Cleans dirty tools and components and protects them from corrosion
  • Stable against acidic and alkaline impurities
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Water displacing with very good wetting behaviour
  • Additive loss due to water contact: Low

WEDOLiT AS 4116

High-Protection-DW-Fluid 60°C flash point, thin film

WEDOLiT AS-4116 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing of rolling.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Extremely low

WEDOLiT AS 4116-3

High-Protection-DW-Fluid 60°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS-4116-3 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Very low

WEDOLiT AS 4143

Dewatering-fluid 60°C flashpoint
(aromatic content ≤ 2%)

WEDOLiT AS 4143 is a dewatering fluid with corrosion protection properties. It uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can be efficiently dewatered. It is mainly used as an immersion bath at room temperature.

  • Due to its strong dewatering effect, residues of flushing water or water containing fluids including emulsions and synthetic coolants are removed from the metal surface
  • After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage
  • Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off
  • Development of a clear phase boundary between the water and the product, without forming an emulsion phase
  • Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
  • Excellent bath-life
  • Additive loss due to water contact: None

WEDOLiT AW 8321 (K 110)

Water-miscible High-performance Fluid

WEDOLiT AW 8321 is universally applicable for parts cleaning and corrosion protection. This mineral oil based product is not only suitable for steel, but also for non-ferrous metals. Utilising the latest technology, AW 8321 offers the possibility for a boron and formaldehyde free application.

  • The product forms a stable emulsion, regardless of the concentration. Due to the electrolyte and temperature stability, an application in heated baths is possible (recommended temperature 60 - 80°C)
  • Even at high temperatures the product is stable against contaminations (e.g. sodium sulfonates or phosphates)
  • Easily removable with solvents or alkaline industrial cleaners
  • For the corrosion protection it´s important that treated parts are completely dry before packaging. Dependent on the concentration a minimal to slightly noticeable film is formed on the metal surface
  • Very good compatibility with VCI foils
  • Outstanding material compatibility (even at higher concentration)

WEDOLiT K 102

Water-miscible high-performance-fluid

WEDOLiT K 102 is universally applicable for part cleaning and corrosion protection. The mineral oil containing product is not only suitable for steel, but also for non-ferrous metals. Based on the latest technology, it offers the possibility for a boron- and formaldehyde-free application.

  • The product forms a stable emulsion, regardless of the concentration
  • Due to the electrolyte and temperature stability, an application in a heated bath is possible (recommended temperature 60 - 80°C)
  • Even at high temperatures the product is stable against contaminations (e.g. sodium sulfonates or phosphates)
  • Easily removable with solvents or alkaline industrial cleaners
  • For corrosion protection it´s important that treated parts are completely dry before packaging
  • Depending on the concentration, a slightly noticeable film is formed on the metal surface
  • Very good compatibility with VCI foils
  • Outstanding material compatibility (even at higher concentration)

WEDOLiT K 119

Basic-Fluid 200°C flash point
(aromatic content ≤ 2%)

WEDOLiT K 119 is a modern formulated corrosion inhibitor for steel and other metals. It offers protection for a short storage period and is suitable for light straightening processes. It can be applied by spraying, flooding or by means of rollers.

Approved by Porsche under PTL 6701-2001-06.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) or to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Suitable for VCI-foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

WEDOLiT K 856

Dewatering, short term RP 100°C

WEDOLiT K 856 is a dewatering fluid with slight corrosion protection properties that uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can be dewatered efficiently. It is mainly used as an immersion bath at room temperature.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31 BImSchV) or to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Due to its strong dewatering effect, residues of flushing water or water containing fluids such as emulsions or synthetic coolants are removed from the metal surface
  • Water/emulsions that enter the bath will settle on the bottom of the tank after a short period and can be drained off
  • Development of a clear phase boundary between the water and the product, without forming an emulsion phase
  • Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
  • Excellent bath-life
  • Additive loss due to water contact: None

WEDOLiT KS 3000

Multi-purpose oil

WEDOLiT KS 3000 is a universally applicable corrosion protection/ rust remover which is also effective in case of moisture-related ignition problems of electrical systems. The product protects chrome parts, tools and machines from atmospheric influences, loosens rusted screws, joints, hinges, switches, cleans tools and parts and protects them from corrosion.

  • Very good creep behaviour (penetrates even very small cavities)
  • Loosens rusted joints
  • Stops squeaking
  • Provides temporary protections against corrosion
  • Very good lubrication properties even at low temperatures
  • To remove heavy staining or corrosion, it might be necessary to repeat the application
  • Water displacing with a very good wetting behaviour
  • Suitable for spot lubrication (e.g. for drilling operations)

WEDOLiT N 22-3

Prelube for deep drawing and stamping

WEDLiT N 22-3 is a thixotropic, non water soluble, deep drawing agent, which was developed for cold forming of coated carbon steels. It is especially applicable for electro galvanised zinc-, zinc nickel coated- and aluminised-sheets. Also good for aluminium and aluminium alloys. The product can be applied by spraying, flooding or rolling.

Fulfils the requirements of all German automotive manufacturers according to VDA-213 and VW-A001, and has been approved by all VDA members.

  • Applications at ambient temperatures possible
  • A preheating of the oil to approximately 40 - 50°C is possible without the loss of the thixotropic effect after cooling
  • Acts at the same time as a corrosion protection agent, and therefore a post treatment of the drawn sheets is not necessary
  • An agent stable film is formed after drawing
  • Can be removed with organic solvents or water soluble, mild alkaline industrial cleaning agents, even after long storage periods
  • After grease removal, excellent phosphating is possible