Login
Home

Forming - Water Miscible Fluids

Number of products in category is 8

WEDOLiT FW 1960

Soap for tube drawing operations

WEDOLiT FW 1960 is a water-soluble alkaline soap for heavy drawing operations of steel tubes. The product is usually used as an immersion bath (bath temperature 75 – 90°C).

  • The product is designed to react with the zinc phosphate layer (which acts as lubricant) to form a zinc soap. The zinc phosphate layer should be at least 4 μm (at heavy forming operations, e.g. cold extrusion, up to 10 μm). Due to specific additives, a maximum conversion of zinc phosphate and the drawing media occurs, which results in an optimal performance regarding degree and rate of deformation
  • Can be used in very low concentrations of 5 - 10% as an aqueous solution (tube drawing). The best results are obtained with water free media
  • Offers (in combination with a zinc phosphate layer) very high cross-sectional reduction and high drawing velocities – up to 100 m/min (steel tubes with standard cross-sectional reduction)


WEDOLiT FW 3500

Water-miscible, fully synthetic coolant

WEDOLiT FW 3500 is a high-pressure agent for hydroforming-processes such as internal and external high pressure forming of steel plates, with different surface qualities and thicknesses. The product can also be applied in different grinding and cooling operations.

Approved by “FF Fluid Forming“

  • Offers very good high-pressure properties
  • Contributes to a high tool life
  • Very good application stability
  • Almost free of foam
  • Offers very good skin compatibility


  • Recommended mixing ratio
  • Hydrofroming:  from 5 - 10%
  • Grinding:  from 3 - 6%


WEDOLiT FW 7651

Water-miscible, fully synthetic coolant

WEDOLiT FW 7651 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

  • Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
  • No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)
  • Can be centrifuged without loss of active substances
  • Removable with organic solvents or alkaline industrial cleaners
  • A bright workpiece surface is obtained after annealing


  • Recommended mixing ratio
  • Tube welding:  from 4 - 6%


WEDOLiT FW 7652

Water-miscible, fully synthetic coolant

WEDOLiT FW 7652 is suitable for wire drawing as well as for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

  • Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
  • No emulsification of mineral oils and engine lubricants. Therefore, the application of a corrosion inhibition oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)
  • Can be centrifuged without loss of active substances
  • Removable with organic solvents or alkaline industrial cleaners
  • A bright workpiece surface is obtained after annealing


  • Recommended mixing ratio
  • Tube welding:  from 4 - 6%
  • Wire drawing:  from 3 - 12%


WEDOLiT FW 7661

Water-miscible, fully synthetic coolant

WEDOLiT FW 7661 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 3 - 5%).

  • Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
  • No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacturing of profiled tubes)
  • Can be centrifuged without loss of active substances
  • Removable with organic solvents or alkaline industrial cleaners
  • A bright workpiece surface is obtained after annealing


  • Recommended mixing ratio
  • Tube welding:  3 -5%


WEDOLiT FW 7840

Water-miscible, semisynthetic coolant

WEDOLiT FW 7840 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration from 7%).

The product is approved by Daimler Chrysler (QSO 040305) under the name WEDOLiT K 911.

  • Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
  • Can be centrifuged without loss of active substances
  • Removable with organic solvents or alkaline industrial cleaners
  • A bright workpiece surface is obtained after annealing


  • Recommended mixing ratio
  • Tube welding:  from 7%


WEDOLiT FW 9200 (C 66)

Water-miscible forming lubricant

WEDOLiT FW 9200 is an ester-based, water-miscible forming lubricant, which can be universally applied in forming (especially drawing) processes of brass and non-ferrous metals.

The application concentration depends on the level of difficulty of the forming operations and has to be determined in preliminary tests. Concentrations of 10 - 15% are usually recommended.

  • Can be applied undiluted as a concentrate
  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Very good material compatibility
  • Easily removable with organic solvents or alkaline industrial cleaners


  • Recommended mixing ratio
  • Drawing operations:  10 - 15%


WEDOLiT FW 9850

Anti spatter fluid

WEDOLiT FW 9850 is a water-miscible anti spatter fluid. The product is usually applied by spraying, but can also be applied with a brush or by means of rollers.

WEDOLiT FW 9850 is approved by Ford (Tox.-Nr. 115412, Mat.Nr. 1180012135), Renault SA (R 100092852) and Peugeot SA (Z 000204960) under the name V 793-357.

  • Delivered as a ready to use product
  • Free of pigments, silicones and chlorine compounds
  • The film that remains on the surface reliably prevents welding beads from adhering to the surface and welding nozzles from becoming encrusted
  • Very good wetting ability
  • Easily removable with alkaline industrial cleaners (even after a longer storage period)