Login
Home

New Products

WEDOLiT CN 2670-18

High performance grinding and cutting oil

WEDOLiT CN 2670-18 is a low viscous, high performance grinding oil for the machining of steel, stainless steel, cast iron, aluminium and non-ferrous metals. The product is also suitable for general cutting operations as well as for gear hobbing.

The product is approved by KAPP NILES under the name N-151-3.

  • High performance product, which leads to an excellent surface finish and dimensional accuracy
  • Highly reduced oil mist formation, almost no loss of evaporation
  • Reduces friction and wear and thus contributes to a long tool life
  • Offers high cooling properties with a very good wetting behaviour
  • Very good flushing behaviour with an optimal transport of chips and swarf
  • Easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT AN 7121

Lanolin-Protection-Fluid 100°C flash point
(aromatic content ≤ 2%)

WEDOLiT AN 7121 is a modern formulated corrosion inhibitor for steel and other metals, which develops a slightly greasy film. The resulting film consists of natural corrosion protection additives with a specific odour. It offers a long-term corrosion protection (indoor storage) and can be applied by spraying, flooding or rolling. Homogenisation before usage is recommended.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) or to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Ideal for VCI-foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Ideal for covered storage
  • Offers protection against atmospheric contamination, e.g. dissolved gases which cannot penetrate the protecting film (water vapour permeability)


WEDOLiT AW 5040

Water-soluble fully synthetic passivating agent

WEDOLiT AW 5040 is a water-soluble passivating agent for steel, which is used as an aqueous solution for a short-term corrosion protection. The product contains no oily or fatty substances and is free of sodium nitrite. Furthermore, it contains a copper and brass inhibitor (for the protection of fittings, etc.).

  • Almost foam free
  • While the protecting film remains water soluble, the product is suitable as a short-term corrosion protection of steel (covered storage)
  • Good skin compatibility


WEDOLiT FN 6160-90

High performance forming oil

WEDOLiT FN 6160-90 is a water-insoluble, chlorinated lubricant for deep drawing and other cold forming operations, e.g. wire drawing, extrusion or thread forming of steel and stainless steel. The undiluted product is usually applied by flooding, spraying, brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieve dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT FN 8830

Special forming oil

WEDOLiT FN 8830 is a chlorine free, pasty, water-insoluble lubricant for cold forming processes (e.g. pilgering) of high alloyed steels. The product is usually applied on the outer diameter by brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • The outstanding extreme-pressure properties combined with an exceptional adhesion offers the possibility for high degrees of deformation
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Contributes to achieving dimensional accuracy
  • Pigments will remain on the surface after annealing and need to be removed (e.g. by pickling with HCl or HNO3) before further processing


WEDOLiT AE 1030

High-Performance-Ester-Fluid

WEDOLiT AE 1030 is a dewatering fluid based on the latest ester technology that uses surface-active substances to displace both water and emulsions from the metal surface quickly. Even highly complex geometries can be efficiently dewatered. It is mainly used as an immersion bath at room temperature.

Not subject to the German solvent guideline VOC 31. BImSCHV or to the Swiss regulation concerning the incentive tax on volatile solvents (VOCV). Fulfils all requirements regarding ELV 2000/53/EG.

  • Due to its strong dewatering effect, residues of flushing water or water containing fluids such as emulsions or synthetic coolants are removed from the metal surface
  • Water/emulsions that enter the bath will settle on the bottom of the tank after a short period and can be drained off
  • Development of a clear phase boundary between the water and the product, without forming an emulsion phase
  • Excellent bath-life
  • Additive loss due to water contact: None


WEDOLiT AE 4313

High-Performance-Ester-Fluid

WEDOLiT AE 4313 is a modern formulated, ester-based corrosion inhibitor for steel and other metals, which offers protection for short overseas transports. It can be applied by spraying, flooding or by means of rollers.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Suitable for short overseas transport
  • No negative labelling
  • Suitable for VCI-foils
  • Stable against acidic and alkaline contamination
  • Excellent material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners


WEDOLiT AN 6111

High-Protection-DW-Fluid 100°C flash point
(aromatic content ≤ 2%)

WEDOLiT AN 6111 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Ideal compatibility with VCI-foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Low


WEDOLiT AN 6141

Special-Fluid 100°C flash point
(aromatic content ≤ 2%)

WEDOLiT AN 6141 is a modern formulated corrosion inhibitor for steel and other metals, which offers good protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) or to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Suitable for overseas transport
  • Suitable for VCI foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline impurities
  • Good material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Water displacing with very good wetting behaviour
  • Additive loss due to water contact: None


WEDOLiT AN 7210

High-Protection-DW-Fluid 130°C flash point
(aromatic content ≤2%)

WEDOLiT AN 7210 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Suitable for overseas transport
  • Ideal compatibility with VCI-foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Low


WEDOLiT AN 7433

High-Protection-DW-Fluid 100°C flash point
(aromatic content ≤2%)

WEDOLiT AN 7433 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, or by means of rollers.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) or to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Ideal compatibility with VCI-foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Low


WEDOLiT AN 9921-100

High-Protection-Calibration-Fluid 100°C flash point
(aromatic content ≤ 2%)

WEDOLiT AN 9921-100 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow bodies. It can also be applied by spraying, flooding or by means of rollers. Due to the high oil content, it can also be used as a straightening oil.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) or to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Can be used as a straightening oil or for light forming processes after the solvent has evaporated
  • Stable against acidic and alkaline contamination
  • Excellent bath life
  • Excellent material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Extremely low


WEDOLiT AS 2111

High-Protection-DW-Fluid 40°C flash point
(aromatic content ≤ 2%)

WEDOiT AS 2111 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Extremely low


WEDOLiT AS 2111-CM

Protection-DW-Fluid 40°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS 2111-CM is a modern formulated corrosion inhibitor for steel and other metals, that offers protection for short overseas transport. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

  • Suitable for overseas transport
  • VCI films suitable: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed, especially before packing in boxes with film
  • Stable against acidic and alkaline impurities
  • Good material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Water displacing with very good wetting behaviour
  • Additive loss due to water contact: Extremely low


WEDOLiT AS 2608

High-Protection-Waxdispersion-Fluid 50°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS 2608 is a universal, solvent-containing, long-term corrosion protection. It contains a newly formulated thixotropic wax dispersion, which allows a long period of protection under covered storage as well as a limited storage period for outdoor storage. It can be applied by spraying, flooding, brushing or by means of rollers.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • After the evaporation of the solvent (quick drying time), a waxy, light-coloured, non-adhesive and non-dust-binding, age-resistant protective film is formed on the treated surface
  • Good protection for outdoor storage
  • It´s recommended to homogenise the product before use or after a longer storage period
  • Protection against atmospheric contaminations such as dissolved gases that cannot penetrate the protective film (water vapour permeability)


WEDOLiT AS 3613

High-Protection-Waxdispersion-Fluid 60°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS 3613 is a universal, solvent-containing, long-term corrosion protection. It contains a newly formulated thixotropic wax dispersion, which allows a long period of protection under covered storage as well as a limited storage period for outdoor storage. It can be applied by spraying, flooding, brushing or by means of rollers.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • After the evaporation of the solvent (quick drying time), a waxy, light-coloured, non-adhesive and non-dust-binding, age-resistant protective film is formed on the treated surface
  • Good protection for outdoor storage
  • It´s recommended to homogenise the product before use or after a longer storage period
  • Protection against atmospheric contaminations such as dissolved gases that cannot penetrate the protective film (water vapour permeability)


WEDOLiT AS 4111-CM

Special-Fluid 60°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS 4111-CM is a modern formulated, universally applicable corrosion protection, which offers a long-term protection (indoor storage). It was especially developed for loosening rusted parts and can be applied by spraying, flooding or can be used as an immersion bath.

  • Suitable for overseas tranpsort
  • Rust remover for humidity-related ignition problems in electrical systems
  • Loosens rusted screws, nuts, joints, hinges, switches and mechanisms
  • Cleans dirty tools and components and protects them from corrosion
  • Stable against acidic and alkaline impurities
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Water displacing with very good wetting behaviour
  • Additive loss due to water contact: Low


WEDOLiT CN 6850-26

High performance oil

WEDOLiT CN 6850-26 is a medium viscous high-performance oil for machining steel, stainless steel, cast iron, aluminium and non-ferrous metals. By using this oil, various processes can be avoided such as separate production lines for machining different materials and the preliminary cleaning of non-ferrous metals. The product can be applied undiluted by spraying, flooding or means of rollers.

  • High performance product, which leads to an excellent surface finish and dimensional accuracy
  • Highly reduced oil mist formation, almost no loss of evaporation
  • Reduces friction and wear and thus contributes to a high tool life
  • Offers high cooling properties with a very good wetting behaviour
  • Very good flushing behaviour for an optimal transport of chips and swarf
  • Easily removable with organic solvents or alkaline industrial cleaners
  • A higher or lower viscosity can be created (equal additive content) by variation of the base oil


WEDOLiT CS 8208

Water-miscible, fully synthetic coolant

WEDOLiT CS 8208 is suitable for ultrasonic testing systems. The product is also suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 5 - 10%). Not suitable for the manufacturing of workpieces made of zinc, aluminium and their alloys.

  • Offers high cooling- and flushing properties with a very good wetting behaviour
  • Contributes to a high tool life
  • Very good application stability
  • Almost free of foam
  • Offers a good skin compatibility
  • Due to its thermal stability, the product can be used in almost the whole process chain of welded tubes (forming, welding, calibration, sawing)


WEDOLiT FN 1170-260

High-performance forming oil

WEDOLiT FN 1170-260 is a medium viscous, chlorine containing forming oil for tube drawing and other cold forming operations of steel. The product also offers an excellent performance for precision cutting operations. The undiluted product is usually applied by spraying, brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieve dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT FN 1190-2300

High-performance forming oil

WEDOLiT FN 1190-2300 is a highly viscous, chlorine containing forming oil for tube drawing and other cold forming operations of stainless steel. The undiluted product is usually applied by brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners
  • Soluble in chlorinated hydrocarbons


WEDOLiT FN 1571-2800

Fully synthetic forming oil

WEDOLiT FN 1571-2800 is a highly viscous, water-insoluble lubricant for tube drawing and other cold forming processes of aluminium and non-ferrous metals. The undiluted product is usually applied by brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners
  • Evaporates at temperatures T ≥ 300°C without leaving any residues or stains on the metal surface. Therefore, no preliminary degreasing is necessary before a potential soft annealing


WEDOLiT FN 2451-850

Fully synthetic forming oil

WEDOLiT FN 2451-850 is a highly viscous, water-insoluble lubricant for wire drawing and other cold forming processes, e.g. deep drawing, extrusion or thread forming, of steel, stainless steel and aluminium. The undiluted product is usually applied by brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT FN 2551-1800

Fully synthetic forming oil

WEDOLiT FN 2551-1800 is a highly viscous, water-insoluble lubricant for wire drawing and other cold forming processes, e.g. deep drawing, extrusion or thread forming, of steel, stainless steel and aluminium. The undiluted product is usually applied by brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT FN 4170-35

High performance forming oil

WEDOLiT FN 4170-35 is a low viscous, water-insoluble chlorinated lubricant for heavy forming operations of steel and stainless steel. A combination of EP additives offers an outstanding performance for precision cutting operations. The undiluted product is usually applied by spraying, dipping, brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT FN 6870-38

High performance forming oil

WEDOLiT FN 6870-38 is a water-insoluble lubricant for wire drawing and other cold forming operations, e.g. deep drawing, extrusion or thread forming, of steel and stainless steel. The undiluted product is usually applied by flooding, spraying, brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT FN 8850-90 is a medium viscous, water-insoluble lubricant for tube drawing and other cold forming operations of steel. Due to the fact that the product also offers corrosion protection, no additional treatment is necessary (for short term storage). The undiluted product is usually applied by spraying, brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT FS 4710

Evaporating forming oil

WEDOLiT FS 4710 is a low viscous, solvent-based lubricant for stamping and forming operations of steel, aluminium and non-ferrous metals. The undiluted product is usually applied by spraying, flooding, brushes or by means of rollers.

  • Good spreading behaviour, which leads to a uniform wetting of the metal surface
  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • If the product is finely dispersed, it evaporates after a short time without leaving any residue. Therefore, an additional cleaning step is not necessary. Otherwise, it is easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT FS 6311

Evaporating forming oil

WEDOLiT FS 6311 is a low viscous, solvent-based lubricant for stamping and forming operations of steel, aluminium and non-ferrous metals, which also performs excellently in thread rolling operations (aluminium). The undiluted product is usually applied by spraying, flooding, brushes or by means of rollers.

  • Good spreading behaviour, which leads to a uniform wetting of the metal surface
  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • If the product is finely dispersed, it evaporates after a short time without leaving any residues. Therefore, an additional cleaning step is not necessary. Otherwise, it is easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT FW 1960

Soap for tube drawing operations

WEDOLiT FW 1960 is a water-soluble alkaline soap for heavy drawing operations of steel tubes. The product is usually used as an immersion bath (bath temperature 75 – 90°C).

  • The product is designed to react with the zinc phosphate layer (which acts as lubricant) to form a zinc soap. The zinc phosphate layer should be at least 4 μm (at heavy forming operations, e.g. cold extrusion, up to 10 μm). Due to specific additives, a maximum conversion of zinc phosphate and the drawing media occurs, which results in an optimal performance regarding degree and rate of deformation
  • Can be used in very low concentrations of 5 - 10% as an aqueous solution (tube drawing). The best results are obtained with water free media
  • Offers (in combination with a zinc phosphate layer) very high cross-sectional reduction and high drawing velocities – up to 100 m/min (steel tubes with standard cross-sectional reduction)


WEDOLiT K 856

Dewatering-fluid 100°C flashpoint
(aromatic content ≤ 2%)

WEDOLiT K 856 is a dewatering fluid with slight corrosion protection properties that uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can be dewatered efficiently. It is mainly used as an immersion bath at room temperature.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31 BImSchV) or to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Due to its strong dewatering effect, residues of flushing water or water containing fluids such as emulsions or synthetic coolants are removed from the metal surface
  • Water/emulsions that enter the bath will settle on the bottom of the tank after a short period and can be drained off
  • Development of a clear phase boundary between the water and the product, without forming an emulsion phase
  • Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
  • Excellent bath-life
  • Additive loss due to water contact: None


WEDOLiT AS 1211 (K 722)

Dewatering-fluid 40°C flashpoint
(aromatic content ≥ 2%)

WEDOLiT AS 1211 is a dewatering fluid with a corrosion protection that uses surface-active substances to displace both water and emulsions from the metal surface extremely quickly. Even highly complex geometries can be quickly and efficiently dewatered. It is mainly used as an immersion bath at room temperature.

The product is approved by DaimlerChrysler (QSO 040212) under the name K 722.

  • Due to its strong dewatering effect, residues of flushing water or water containing fluids such as emulsions or synthetic coolants are removed from the metal surface
  • After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage
  • Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off
  • Development of a clear phase boundary between the water and the product, without forming an emulsion phase
  • Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
  • Excellent bath-life
  • Additive loss due to water contact: None


WEDOLiT AW 7010 (K 91-V)

Water-miscible high-performance-fluid

WEDOLiT AW 7010 is universally applicable for part cleaning and corrosion protection. The mineral oil free product is not only suitable for steel, but also for non-ferrous metals. Based on the latest technology, it offers the possibility for a boron- and formaldehyde free application.

  • The product forms a stable emulsion, regardless of the concentration. Due to the electrolyte- and temperature stability, an application in heated baths is possible (recommended temperature 60 - 80°C)
  • Even at high temperatures, the product is stable against contaminations (e.g. sodium sulfonates or -phosphates)
  • Easily removable with solvents or alkaline industrial cleaners
  • For the corrosion protection it´s important that treated parts are completely dry before packaging
  • Dependent on the concentration, a hardly to slightly noticeable film is formed on the metal surface
  • Very good compatibility with VCI foils
  • Outstanding material compatibility (even at higher concentration)


WEDOLiT AS 2241-1

High-Protection-DW-Fluid 40°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS 2241-1 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Extremely low


WEDOLiT AS 2241-3

High-Protection-DW-Fluid 40°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS-2241-3 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Low


WEDOLiT AS 4116-3

High-Protection-DW-Fluid 60°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS-4116-3 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Very low


WEDOLiT AW 8321 (K 110)

Water-miscible High-performance Fluid

WEDOLiT AW 8321 is universally applicable for parts cleaning and corrosion protection. The mineral oil free product is not only suitable for steel, but also for non-ferrous metals. Utilising the latest technology, AW 8321 offers the possibility for a boron and formaldehyde free application.

  • The product forms a stable emulsion, regardless of the concentration. Due to the electrolyte and temperature stability, an application in heated baths is possible (recommended temperature 60 - 80°C)
  • Even at high temperatures the product is stable against contaminations (e.g. sodium sulfonates or phosphates)
  • Easily removable with solvents or alkaline industrial cleaners
  • For the corrosion protection it´s important that treated parts are completely dry before packaging. Dependent on the concentration a minimal to slightly noticeable film is formed on the metal surface
  • Very good compatibility with VCI foils
  • Outstanding material compatibility (even at higher concentration)


WEDOLiT AS 2241

High-Protection-DW-Fluid 40°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS-2241 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Extremely low


WEDOLiT CW 8906

Water-miscible, ester-based coolant

WEDOLiT CW 8906 is suitable for grinding as well as light to heavy cutting operations of steel, stainless steel, aluminium and titanium.

  • Offers high cooling- and flushing properties with a very good wetting behaviour
  • Contributes to a high tool life
  • Very good application stability
  • Almost free of foam
  • Offers a very good skin compatibility


WEDOLiT AS 9921-80

High-Protection-Calibration-Fluid 80°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS 9921-80 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow bodies. It can also be applied by spraying, flooding, brushing or rolling. Due to the high oil content, it can also be used in straightening processes.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Can be used in straightening or light forming processes after the solvent has evaporated
  • Stable against acidic and alkaline contamination
  • Excellent bath life
  • Excellent material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Extremely low


WEDOLiT AN 6723

Special-Fluid 100°C flash point
(aromatic content ≤ 2%)

WEDOLiT AN 6723 is a thixotropic corrosion protection oil for steel. It contains a combination of inhibitors which offers long-term protection for indoor storage and short-term protection for outdoor storage. It can be applied by spraying, flooding, brushing or rolling.
WEDOLiT AN 6723 fulfills all requirements regarding Altautorichtlinie 2000/53/EG. It is not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Ideal for overseas transport
  • Stable against acidic and alkaline impurities
  • Good material compatibility
  • The full corrosion protection develops, if the product is applied at temperatures of 50 - 60°C (for spraying: The temperature has to be adapted according to the specifications of the used device)
  • For an optimal protection of the treated parts, storage temperatures ≥ 36°C and a direct exposure to solar radiation should be avoided


WEDOLiT AS 4143

Dewatering-fluid 60°C flashpoint
(aromatic content ≤ 2%)

WEDOLiT AS 4143 is a dewatering fluid with corrosion protection properties. It uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can be efficiently dewatered. It is mainly used as an immersion bath at room temperature.

  • Due to its strong dewatering effect, residues of flushing water or water containing fluids including emulsions and synthetic coolants are removed from the metal surface
  • After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage
  • Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off
  • Development of a clear phase boundary between the water and the product, without forming an emulsion phase
  • Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
  • Excellent bath-life
  • Additive loss due to water contact: None


WEDOLiT FW 7661

Water-miscible, fully synthetic coolant

WEDOLiT FW 7661 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 3 - 5%).

  • Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
  • No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacturing of profiled tubes)
  • Can be centrifuged without loss of active substances
  • Removable with organic solvents or alkaline industrial cleaners
  • A bright workpiece surface is obtained after annealing


  • Recommended mixing ratio
  • Tube welding:  3 -5%


WEDOLiT AS 4116-2

High-Protection-DW-Fluid 60°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS-4116-2 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Extremely low


WEDOLiT AN 7324

Special-Fluid 100°C flash point
(aromatic content ≤ 2%)

WEDOLiT AN 7324 is a leading edge corrosion inhibitor for steel and other metals. It can be applied by spraying, flooding, brushing or rolling on parts with surface temperatures ≤ 80°C. This results in time savings and enhances productivity.

WEDOLiT AN 7324 fulfills all requirements regarding Altautorichtlinie 2000/53/EG. It is not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Parts with surface temperatures ≤ 80°C can be treated without odour formation or a loss in performance
  • Suitable for VCI foils
  • Stable against acidic and alkaline impurities
  • Good material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Water displacing with a very good wetting behaviour


WEDOLiT AS 9921-40

High-Protection-Calibration-Fluid 40°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS 9921-40 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow bodies. It can also be applied by spraying, flooding, brushing or rolling. Due to the high oil content, it can also be used in straightening processes.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Can be used in straightening or light forming processes after the solvent has evaporated
  • Stable against acidic and alkaline contamination
  • Excellent bath life
  • Excellent material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Extremely low


WEDOLiT AS 9921-60

High-Protection-Calibration-Fluid 60°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS 9921-60 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow bodies. It can also be applied by spraying, flooding, brushing or rolling. Due to the high oil content, it can also be used in straightening processes.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Can be used in straightening or light forming processes after the solvent has evaporated
  • Stable against acidic and alkaline contamination
  • Excellent bath life
  • Excellent material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Extremely low


WEDOLiT CS 9040

Water-miscible, fully synthetic coolant

WEDOLiT CS 9040 is suitable for grinding steel and glass. The product is also suitable as a press water medium for tubes.

  • Offers high cooling- and flushing properties with a very good wetting behaviour
  • Contributes to a high tool life
  • Very good application stability
  • Almost free of foam
  • Offers good skin compatibility


WEDOLiT AS 1012

Dewatering-fluid 40°C flashpoint
(aromatic content ≤ 2%)

WEDOLiT AS 1012 is a dewatering fluid with corrosion protection properties. It uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can efficiently be dewatered. It is mainly used as an immersion bath at room temperature.

  • Due to its strong dewatering effect, residues of flushing water or water containing fluids including emulsions or synthetic coolants are removed from the metal surface
  • After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage
  • Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off
  • Development of a clear phase boundary between the water and the product, without forming an emulsion phase
  • Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
  • Excellent bath-life
  • Additive loss due to water contact: None


WEDOLiT FW 7651

Water-miscible, fully synthetic coolant

WEDOLiT FW 7651 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

  • Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
  • No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)
  • Can be centrifuged without loss of active substances
  • Removable with organic solvents or alkaline industrial cleaners
  • A bright workpiece surface is obtained after annealing


  • Recommended mixing ratio
  • Tube welding:  from 4 - 6%


WEDOLiT FW 7840

Water-miscible, semisynthetic coolant

WEDOLiT FW 7840 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration from 7%).

The product is approved by Daimler Chrysler (QSO 040305) under the name WEDOLiT K 911.

  • Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
  • Can be centrifuged without loss of active substances
  • Removable with organic solvents or alkaline industrial cleaners
  • A bright workpiece surface is obtained after annealing


  • Recommended mixing ratio
  • Tube welding:  from 7%


WEDOLiT FW 7652

Water-miscible, fully synthetic coolant

WEDOLiT FW 7652 is suitable for wire drawing as well as for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

  • Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
  • No emulsification of mineral oils and engine lubricants. Therefore, the application of a corrosion inhibition oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)
  • Can be centrifuged without loss of active substances
  • Removable with organic solvents or alkaline industrial cleaners
  • A bright workpiece surface is obtained after annealing


  • Recommended mixing ratio
  • Tube welding:  from 4 - 6%
  • Wire drawing:  from 3 - 12%


WEDOLiT CW 9206

Water-miscible, semi synthetic coolant

WEDOLiT CW 9206 is suitable for grinding as well as light to heavy cutting operations of steel, cast iron and aluminium.

  • Offers high cooling- and flushing properties with a very good wetting behaviour
  • Contributes to a high tool life
  • Very good application stability
  • Good soft water stability (at approximately 10°dH)
  • Almost free of foam
  • Offers a very good skin compatibility


WEDOLiT AS 2251

High-Protection-DW-Fluid 40°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS-2251 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Very low


WEDOLiT CS 8376

Water-miscible, fully synthetic polymer-based coolant

WEDOLiT CS 8376 is suitable for grinding as well as for light to heavy cutting operations of steel, stainless steel, cast iron, aluminium, titanium and non-ferrous metals.

  • Offers high cooling- and flushing properties with a very good wetting behaviour
  • Contributes to a high tool life (especially in difficult machining operations of titanium or Inconel)
  • Very good application stability
  • Almost free of foam
  • Offers very good skin compatibility


WEDOLiT AS 3040

Dewatering-fluid 60°C flashpoint
(aromatic content ≤ 2%)

WEDOLiT AS 3040 is a dewatering fluid with corrosion protection properties that uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can be efficiently dewatered. It is mainly used as an immersion bath at room temperature.

  • Due to its strong dewatering effect, residues of flushing water or water containing fluids including emulsions and synthetic coolants are removed from the metal surface
  • After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage
  • Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off
  • Development of a clear phase boundary between the water and the product, without forming an emulsion phase
  • Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
  • Excellent bath-life
  • Additive loss due to water contact: None


WEDOLiT CW 9006-CM

Water-miscible, semi synthetic coolant

WEDOLiT CW 9006-CM is suitable for grinding as well as light to medium cutting operations of steel, stainless steel and cast iron.

  • Offers high cooling- and flushing properties with a very good wetting behaviour
  • Contributes to a high tool life
  • Very good application stability
  • Good soft water stability (at approximately 10°dH)
  • Almost free of foam
  • Offers a good skin compatibility


WEDOLiT CS 9016

Water-soluble coolant

WEDOLiT CS 9016 is a water soluble, high performance coolant for different grinding and machining operations (steel and ferrous metals). The product can also be used as a cooling agent for tube-welding- and profiling machines and is also suitable as a transmission fluid for hydraulic presses (e.g. U- and O-presses) or as a lubricating-/anti corrosion agent for hydro testing.

  • Very good flushing behaviour and wettability
  • Contributes to a high tool life
  • Almost no foam generation
  • Very good application stability


  • Recommended mixing ratio
  • Hydro tester or for grinding operations:  2.5 - 3.5%
  • Cooling lubricant for tube-welding and profiling machines:  4.0 - 5.0%
  • Machining or forming operations:  4.0 - 7.0%


WEDOLiT AN 7114

High-Protection-DW-Fluid 120°C flash point
(aromatic content ≤ 2%)

WEDOLiT AN-7114 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

WEDOLiT AN-7114 fulfills all requirements regarding Altautorichtlinie 2000/53/EG. It is not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Ideal compatibility with VCI-foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Low


WEDOLiT AS 4116

High-Protection-DW-Fluid 60°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS-4116 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing of rolling.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Extremely low


WEDOLiT FN 4455-55

Conventional forming oil

WEDOLiT FN 4455-55 is a low viscous, water-insoluble lubricant for heavy forming operations of steel and non-ferrous metals. A combination of EP additives offers a outstanding performance for precision cutting operations. The undiluted product is usually applied by spraying, dipping, brushing or rolling.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a long tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT FN 2451-150

Semisynthetic forming oil

WEDOLiT FN 2451-150 is a medium viscous, water-insoluble lubricant for wire drawing and other cold forming processes, e.g. deep drawing, extrusion or thread forming, of steel, stainless steel and aluminium. The undiluted product is usually applied by brushes or rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a long tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieve dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT CS 9203

Water-soluble, fully synthetic coolant

WEDOLiT CS 9203 can be used for different metalworking operations on steel and ferrous metals in grinding, cutting operations as well as a cooling agent for tube-welding and profiling machines. Especially adequate as a transmission fluid for hydraulic presses (e.g. U- and O-presses) or a lubricating /anti corrosion agent in hydro testers.

  • Good lubrication performance
  • Good corrosion protection
  • Very good rinsing behaviour (especially when sanding)
  • Very good long-term stability even under demanding conditions
  • Leads to long tool life
  • Very good foaming behaviour


WEDOLiT FN 1490-850

Fully Synthetic Forming Oil

WEDOLiT FN 1490-850 is a highly viscous, water-insoluble lubricant for tube drawing and other cold forming processes of aluminium and non-ferrous metals. The undiluted product is usually applied by brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a long tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, preventing stick-slip and chatter
  • Leads to clean surfaces and contributes to dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners
  • Evaporates at temperatures T ≥ 300°C without leaving any residue or stains on the metal surface and therefore, no preliminary degreasing is necessary before a potential soft annealing


WEDOLiT FS 3710

Evaporating Drawing-oil

WEDOLiT FS 3710 is a non-water soluble, synthetic cooling lubricant of low viscosity. It is applicable for drawing- and punching-operations of aluminium. Can be applied undiluted by spraying, flooding, brushing or rolling.

  • Good wetting of the metal surface
  • Nearly odourless
  • Despite the good lubrication properties, the product is characterised by a quick evaporation and high flash point
  • The working area should be sufficiently ventilated, due to the amount of volatile hydrocarbons


WEDOLiT FN 6870-170

Conventional Forming Oil

WEDOLiT FN 6870-170 is a medium viscous, water-insoluble lubricant for deep drawing and other cold forming processes of steel (e.g. for auto bodies). Additionally, the product is suitable as a spot lubricant for thread cutting or blind hole drilling. The undiluted product is usually applied by spraying, dipping, brushes or by means of rollers.

The product meets the requirements of the test procedure according to VDA 230-213.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieve dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT CW 8006

Water-miscible, semi synthetic coolant

WEDOLiT CW 8006 is suitable for light to heavy cutting operations of steel, stainless steel, cast iron and aluminium.

  • Offers high cooling- and flushing properties with a very good wetting behaviour
  • Contributes to a high tool life
  • Very good application stability
  • Almost free of foam
  • Offers a good skin compatibility


WEDOLiT EP 1090-E

Expander oil

WEDOLiT EP 1090-E is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for utilisation in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents the stick-slip- effect due to the high content of polar additives.

  • Very high film stability (even under high pressures)
  • Good adhesion properties on smooth surfaces, very good wear protection
  • Easily removable with water (spontaneous emulsification)
  • The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be easily separated into water and oily waste by the utilization of specific additives
  • The treated water can be reused for the preparation of a new emulsion (to a certain degree)


WEDOLiT AS 1723

High-Protection-Waxdispersion-Fluid 30°C flash point
(aromatic content ≤ 2%)

WEDOLIiT AS 1723 is a universal, solvent-containing, long-term corrosion protection. It contains a newly formulated thixotropic wax dispersion, which allows a long period of protection under covered storage as well as a limited period of outdoor storage. It can be applied by spraying, flooding, brushing or by means of rollers.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • After the evaporation of the solvent (quick drying time), a waxy, light-coloured, non-adhesive and non-dust-binding, age-resistant protective film is formed on the treated surface
  • Good protection for outdoor storage
  • It´s recommended to homogenise the product before use or after a longer storage period
  • Protection against atmospheric contaminations such as dissolved gases that cannot penetrate the protective film (water vapour permeability)


WEDOLiT AS 4111

Special-Fluid 60°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS 4111 is a leading edge universally applicable, corrosion protection which offers a long-term protection for indoor storage. It has been especially developed for loosening rusted parts and can be applied by spraying, flooding or via an immersion bath.

  • Suitable for overseas tranpsort
  • Rust remover for humidity-related ignition problems in electrical systems
  • Loosens rusted screws, nuts, joints, hinges, switches and mechanisms
  • Cleans dirty tools and components and protects them from corrosion
  • Stable against acidic and alkaline impurities
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Water displacing with very good wetting behaviour
  • Additive loss due to water contact: Low


WEDOLiT FW 9850

Anti spatter fluid

WEDOLiT FW 9850 is a water-miscible anti spatter fluid. The product is usually applied by spraying, but can also be applied with a brush or by means of rollers.

WEDOLiT FW 9850 is approved by Ford (Tox.-Nr. 115412, Mat.Nr. 1180012135), Renault SA (R 100092852) and Peugeot SA (Z 000204960) under the name V 793-357.

  • Delivered as a ready to use product
  • Free of pigments, silicones and chlorine compounds
  • The film that remains on the surface reliably prevents welding beads from adhering to the surface and welding nozzles from becoming encrusted
  • Very good wetting ability
  • Easily removable with alkaline industrial cleaners (even after a longer storage period)


WEDOLiT FN 8471

Special forming oil

WEDOLiT FN 8471 is a chlorine free, pasty, water-insoluble lubricant for cold forming processes (e.g. pilgering) of high alloyed steels. The product is usually applied by brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • The outstanding extreme-pressure properties combined with an exceptional adhesion offers the possibility for high degrees of deformation
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Contributes to achieving dimensional accuracy
  • Before pilgering: Sicromal steels should be pre-heated to 200 - 280°C
  • Pigments will remain on the surface after annealing and should be removed (e.g. by pickling with HCl or HNO3) before further processing


WEDOLiT CS 6206

Water-miscible, fully synthetic coolant

WEDOLiT CS 6206 is suitable for grinding of steel, cast iron, aluminium, non-ferrous metals, glass and especially carbides.

  • Offers high cooling- and flushing properties with a very good wetting behaviour
  • Contributes to a high tool life
  • Very good application stability
  • Almost free of foam
  • Offers a good skin compatibility


  • Recommended mixing ratio
  • Grinding:  from 4%
  • General cutting:  from 6%


WEDOLiT CS 6201

Water-miscible, fully synthetic coolant

WEDOLiT CS 6201 is suitable for grinding of steel, cast iron, aluminium, non-ferrous metals, glass and especially carbides.

  • Offers high cooling- and flushing properties with a very good wetting behaviour
  • Contributes to a high tool life
  • Very good application stability
  • Almost free of foam
  • Offers good skin compatibility


WEDOLiT CN 3370-21

High performance cutting oil

WEDOLiT CN 3370-21 is a low viscous, high performance cutting oil based on the latest gas to liquid (GTL) technology. The product is suitable for deep hole drilling of steel, stainless steel and aluminium. The product is also suitable for general cutting operations as well as for gear hobbing.

  • High performance product, which leads to an excellent surface finish and dimensional accuracy
  • Special additiviation for deep hole drilling
  • Highly reduced oil mist formation, almost no loss of evaporation
  • Reduces friction and wear and thus contributes to a high tool life
  • Offers high cooling properties with a very good wetting behaviour
  • Very good flushing behaviour with an optimal transport of chips and swarf
  • Easily removable with organic solvents or alkaline industrial cleaners