Login
Home


Leading Solutions for Tubes
Leading Solutions for Tubes

Outstanding dewatering fluids

Hard wax, very resistant against mechanical influences
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Yellow, cloudy to clear Visual
Density at 15°C: Not measurable ASTM D 7042
Viscosity at 20°C: Not measurable ASTM D 7042
Flash point: > 40 °C DIN EN ISO 2719
Film weight: 3.0 g/m2 Dipping procedure
Film type: Waxy Haptical
Dewatering effect: ≤ 10 s Internal test method
Water separation: 4 min Internal test method
Humidity test: 180 cycles DIN EN ISO 6270-2 AHT
Salt spray performance: 2 h DIN EN ISO 9227 NSS
Very fast dewatering, offers short-term corrosion protection, lower flash point
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Bright yellow, clear Visual
Density at 15°C: 0.79 g/cm3 ASTM D 7042
Viscosity at 20°C: 2.2 mm2/s ASTM D 7042
Flash point: > 40 °C DIN EN ISO 2719
Film weight: 0.3 g/m2 Dipping procedure
Film type: Very slightly oily Haptical
Dewatering effect: ≤ 5 s Internal test method
Water separation: 4 min Internal test method
Humidity test: 10 cycles DIN EN ISO 6270-2 AHT
Salt spray performance: < 1 h DIN EN ISO 9227 NSS
Very fast dewatering, offers short-term corrosion protection, higher flash point
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Bright yellow, clear Visual
Density at 15°C: 0.80 g/cm3 ASTM D 7042
Viscosity at 20°C: 2.8 mm2/s ASTM D 7042
Flash point: > 60 °C DIN EN ISO 2719
Film weight: 0.3 g/m2 Dipping procedure
Film type: Very slightly oily Haptical
Dewatering effect: ≤ 5 s Internal test method
Water separation: 4 min Internal test method
Humidity test: 7 cycles DIN EN ISO 6270-2 AHT
Salt spray performance: < 1 h DIN EN ISO 9227 NSS
Very fast dewatering, offers short-term corrosion protection, VOC free version
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Bright yellow, clear Visual
Density at 15°C: 0.81 g/cm3 ASTM D 7042
Viscosity at 20°C: 4.1 mm2/s ASTM D 7042
Flash point: > 100 °C DIN EN ISO 2719
Film weight: 0.3 g/m2 Dipping procedure
Film type: Very slightly oily Haptical
Dewatering effect: ≤ 5 s Internal test method
Water separation: 4 min Internal test method
Humidity test: 7 cycles DIN EN ISO 6270-2 AHT
Salt spray performance: < 1 h DIN EN ISO 9227 NSS

High corrosion protection with dewatering effect

Outstanding universal corrosion protection for long-term overseas transportation
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Brown, clear Visual
Density at 15°C: 0.81 g/cm3 ASTM D 7042
Viscosity at 20°C: 2.2 mm2/s ASTM D 7042
Flash point: > 40 °C DIN EN ISO 2719
Film weight: 1.4 g/m2 Dipping procedure
Film type: Oily Haptical
Dewatering effect: ≤ 30 s Internal test method
Water separation: 8 min Internal test method
Humidity test: 150 cycles DIN EN ISO 6270-2 AHT
Salt spray performance: 60 h DIN EN ISO 9227 NSS
Thin film wax corrosion protection, no influence on subsequent processes, for mid-term storage
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Medium-brown, clear Visual
Density at 15°C: 0.81 g/cm3 ASTM D 7042
Viscosity at 20°C: 2.3 mm2/s ASTM D 7042
Flash point: > 60 °C DIN EN ISO 2719
Film weight: 0.5 g/m2 Dipping procedure
Film type: Microwax Haptical
Dewatering effect: ≤ 30 s Internal test method
Water separation: 4 min Internal test method
Humidity test: 90 cycles DIN EN ISO 6270-2 AHT
Salt spray performance: 24 h DIN EN ISO 9227 NSS
Corrosion protection with an outstanding performance, for overseas long-term transportation
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Medium-brown, clear Visual
Density at 15°C: 0.82 g/cm3 ASTM D 7042
Viscosity at 20°C: 2.8 mm2/s ASTM D 7042
Flash point: > 60 °C DIN EN ISO 2719
Film weight: 1.4 g/m2 Dipping procedure
Film type: Oily Haptical
Dewatering effect: ≤ 30 s Internal test method
Water separation: 9 min Internal test method
Humidity test: 120 cycles DIN EN ISO 6270-2 AHT
Salt spray performance: 48 h DIN EN ISO 9227 NSS
VOC free for short-term corrosion protection
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Yellow-medium-brown, clear Visual
Density at 15°C: 0.86 g/cm3 ASTM D 7042
Viscosity at 20°C: 13.8 mm2/s ASTM D 7042
Flash point: > 120 °C DIN EN ISO 2719
Film weight: 1.5 g/m2 Dipping procedure
Film type: Oily Haptical
Dewatering effect: ≤ 30 s Internal test method
Water separation: 17 min Internal test method
Humidity test: 50 cycles DIN EN ISO 6270-2 AHT
Salt spray performance: 2 h DIN EN ISO 9227 NSS

High corrosion protection, wax dispersion

Thick, waxy high performance product, potentially for outdoor storage
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Black, cloudy Visual
Density at 15°C: 0.81 g/cm3 ASTM D 7042
Viscosity at 20°C: 74.0 mm2/s ASTM D 7042
Flash point: > 38 °C DIN EN ISO 2719
Film weight: 28.0 g/m2 Dipping procedure
Film type: Waxy Haptical
Dewatering effect: None Internal test method
Water separation: None Internal test method
Humidity test: 1500 cycles DIN EN ISO 6270-2 AHT
Salt spray performance: 220 h DIN EN ISO 9227 NSS

High corrosion protection, straightening oils

Ideal for short-term corrosion protection of dry workpieces, suitable for light forming operations, VOC free
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Brown, clear Visual
Density at 15°C: 0.85 g/cm3 ASTM D 7042
Viscosity at 20°C: 10.5 mm2/s ASTM D 7042
Flash point: > 100 °C DIN EN ISO 2719
Film weight: 1.2 g/m2 Dipping procedure
Film type: Oily Haptical
Dewatering effect: None Internal test method
Water separation: 18 min Internal test method
Humidity test: 60 cycles DIN EN ISO 6270-2 AHT
Salt spray performance: 24 h DIN EN ISO 9227 NSS

Specialist fluids for special applications

Multi-purpose oil, with forming properties, also available in aerosol cans (WEDOLiT KS 3000)
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Medium-brown, clear Visual
Density at 15°C: 0.83 g/cm3 ASTM D 7042
Viscosity at 20°C: 4.4 mm2/s ASTM D 7042
Flash point: > 60 °C DIN EN ISO 2719
Film weight: 1.8 g/m2 Dipping procedure
Film type: Oily Haptical
Dewatering effect: ≤ 60 s Internal test method
Water separation: 5 min Internal test method
Humidity test: 70 cycles DIN EN ISO 6270-2 AHT
Salt spray performance: 8 h DIN EN ISO 9227 NSS
Very high protection product, no negative labelling, VOC free, potentially for outdoor storage
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Medium-brown, turbid, pasty Visual
Density at 15°C: 0.90 g/cm3 ASTM D 7042
Viscosity at 20°C: Not measurable ASTM D 7042
Flash point: > 100 °C DIN EN ISO 2719
Film weight: Depending on the application Dipping procedure
Film type: Waxy Haptical
Dewatering effect: None Internal test method
Water separation: None Internal test method
Humidity test: 1800 cycles DIN EN ISO 6270-2 AHT
Salt spray performance: 35 h DIN EN ISO 9227 NSS
Application at surface temperatures up to 80 °C, GTL-oil, VOC free, no negative labelling
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Medium-brown, turbid-clear Visual
Density at 15°C: 0.83 g/cm3 ASTM D 7042
Viscosity at 20°C: 20.5 mm2/s ASTM D 7042
Flash point: > 160 °C DIN EN ISO 2719
Film weight: 1.7 g/m2 Dipping procedure
Film type: Oily Haptical
Dewatering effect: ≤ 70 s Internal test method
Water separation: None Internal test method
Humidity test: 70 cycles DIN EN ISO 6270-2 AHT
Salt spray performance: 12 h DIN EN ISO 9227 NSS

New generation ester-based corrosion protection

Ester-based dewatering fluid, no negative labelling, mineral oil free
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Light yellow, clear Visual
Density at 15°C: 0.86 g/cm3 ASTM D 7042
Viscosity at 20°C: 11.2 mm2/s ASTM D 7042
Flash point: > 160 °C DIN EN ISO 2719
Film weight: 0.5 g/m2 Dipping procedure
Film type: Slightly oily Haptical
Dewatering effect: ≤ 30 s Internal test method
Water separation: 12 min Internal test method
Humidity test: 14 cycles DIN EN ISO 6270-2 AHT
Salt spray performance: < 1 h DIN EN ISO 9227 NSS
Ester-based corrrosion protection, no negative labelling, mineral oil free
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Yellow, clear Visual
Density at 15°C: 0.87 g/cm3 ASTM D 7042
Viscosity at 20°C: 13.6 mm2/s ASTM D 7042
Flash point: > 160 °C DIN EN ISO 2719
Film weight: 0.5 g/m2 Dipping procedure
Film type: Slightly oily Haptical
Dewatering effect: None Internal test method
Water separation: None Internal test method
Humidity test: 30 cycles DIN EN ISO 6270-2 AHT
Salt spray performance: 8 h DIN EN ISO 9227 NSS

Water-miscible corrosion protection

Water-miscible parts cleaner, very good corrosion protection, application at approximately 60°C, for steel and non-ferrous metals
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Dark brown, clear-slightly turbid Visual
Density at 15°C: 0.91 g/cm3 ASTM D 7042
Viscosity at 40°C: 44.0 mm2/s ASTM D 7042
Flash point: > 100 °C DIN EN ISO 2719
pH-value [20%; 70°C]: 9.8 DIN EN ISO 10523
Conductivity [20%; 70°C]: 1850 µS/cm DIN EN 27888
Corrosion protection properties
Concentration: 10% 20% 100% Tested according to
Film weight: 1.8 g/m2 4.7 g/m2 5.2 g/m2 Dipping procedure
Humidity test: > 1 d > 2 d > 4 d DIN EN ISO 6270-2 AHT
Salt spray performance: < 2 h < 16 h > 24 h DIN EN ISO 9227 NSS
Water-miscible parts cleaner, application at approximately 60°C, for steel and non-ferrous metals, Rattunde approval
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Dark brown, clear-slightly turbid Visual
Density at 15°C: 0.97 g/cm3 ASTM D 7042
Viscosity at 40°C: 108.0 mm2/s ASTM D 7042
Flash point: > 100 °C DIN EN ISO 2719
pH-value [20%; 70°C]: 9.6 DIN EN ISO 10523
Conductivity [20%; 70°C]: 4500 µS/cm DIN EN 27888
Corrosion protection properties
Concentration: 10% 20% 100% Tested according to
Film weight: 0.8 g/m2 1.2 g/m2 5.2 g/m2 Dipping procedure
Humidity test: > 1 d > 2 d > 4 d DIN EN ISO 6270-2 AHT
Salt spray performance: < 1 h < 1 h > 1 h DIN EN ISO 9227 NSS

Tube welding solutions / Emulsions

Fully synthetic tube welding medium for bright steel
Physical Properties Typical Data
Concentrate
Colour Mineral oil content Viscosity at 20°C:
ASTM D 7042
Density at 20°C:
ASTM D 7042
Copper corrosion:
DIN 51759-1
Yellow, clear Free 6.6 mm2/s 1.06 Not determined*
5% Solution
Colour pH-value
(tap water)
Corrosion protection
DIN 51360-2
Refractometer factor (brix) Conductivity
(Deionised water)
Clear 9.4 5 % grade 0 2.3 1940 μS/cm
Characteristics
Mineral oil EP-additives Chlorine Boron Amines FAD
- + - + + +
*Discolourations of non-ferrous metals should be examined in preliminary tests
For welding of galvanised steel tubes, mineral oil free
Physical Properties Typical Data
Concentrate
Colour Mineral oil content Viscosity at 20°C:
ASTM D 7042
Density at 20°C:
ASTM D 7042
Copper corrosion:
DIN 51759-1
Yellow, clear Free 6.1 mm2/s 1.08 Not determined*
5% Solution
Colour pH-value
(tap water)
Corrosion protection
DIN 51360-2
Refractometer factor (brix) Conductivity
(Deionised water)
Clear 9.5 5 % grade 0 2.3 3090 μS/cm
Characteristics
Mineral oil EP-additives Chlorine Boron Amines FAD
- - - + + +
*Discolourations of non-ferrous metals should be examined in preliminary tests
Fully synthetic tube welding medium for bright steel, boron free version of FW 7651
Physical Properties Typical Data
Concentrate
Colour Mineral oil content Viscosity at 20°C:
ASTM D 7042
Density at 20°C:
ASTM D 7042
Copper corrosion:
DIN 51759-1
Yellow, clear Free 8.0 mm2/s 1.06 Not determined*
5% Solution
Colour pH-value
(tap water)
Corrosion protection
DIN 51360-2
Refractometer factor (brix) Conductivity
(Deionised water)
Clear 9.4 5 % grade 0 2.3 1590 μS/cm
Characteristics
Mineral oil EP-additives Chlorine Boron Amines FAD
- + - - + +
*Discolourations of non-ferrous metals should be examined in preliminary tests
Tube welding emulsion for bright and galvanised steel
Physical Properties Typical Data
Concentrate
Colour Mineral oil content Viscosity at 20°C:
ASTM D 7042
Density at 20°C:
ASTM D 7042
Copper corrosion:
DIN 51759-1
Brown 30 % 186.0 mm2/s 0.98 Not determined*
5% Solution
Colour pH-value
(tap water)
Corrosion protection
DIN 51360-2
Refractometer factor (brix) Conductivity
(Deionised water)
Whitish 9.2 5 % grade 0 1.0 1550 μS/cm
Characteristics
Mineral oil EP-additives Chlorine Boron Amines FAD
+ - - - - +
*Discolourations of non-ferrous metals should be examined in preliminary tests

Tube and wire manufacturing

High performance oil for drawing of steel and stainless steel wires, contains chlorine
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Yellow Visual
Density at 20°C: 1.45 g/cm3 ASTM D 7042
Viscosity at 40°C: 2335.0 mm2/s ASTM D 7042
Flash point: > 190 °C DIN EN ISO 2719
Copper corrosion: Not determined* DIN 51759-1
*Discolourations of non-ferrous metals should be examined in preliminary tests
Drawing oil for copper, cupronickel and aluminum tubes, available in different viscosities
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Clear Visual
Density at 20°C: 0.90 g/cm3 ASTM D 7042
Viscosity at 40°C: 850.0 mm2/s ASTM D 7042
Flash point: > 160 °C DIN EN ISO 2719
Copper corrosion: 1a DIN 51759-1
For copper and copper-iron alloys
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Clear Visual
Density at 20°C: 0.90 g/cm3 ASTM D 7042
Viscosity at 40°C: 2780.0 mm2/s ASTM D 7042
Flash point: > 160 °C DIN EN ISO 2719
Copper corrosion: 1a DIN 51759-1
Chlorine free pilger paste for stainless steel tubes
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Beige Visual
Density at 20°C: 1.20 g/cm3 ASTM D 7042
Viscosity at 40°C: Not measurable ASTM D 7042
Flash point: > 100 °C DIN EN ISO 2719
Copper corrosion: Not determined* DIN 51759-1
*Discolourations of non-ferrous metals should be examined in preliminary tests
For drawing of tubes with small diameters (e.g. for diesel injection lines)
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Brown, clear Visual
Density at 20°C: 0.90 g/cm3 ASTM D 7042
Viscosity at 40°C: 90.0 mm2/s ASTM D 7042
Flash point: > 220 °C DIN EN ISO 2719
Copper corrosion: 1b DIN 51759-1
Evaporating straightening and polishing oil for aluminum and brass tubes, quickly evaporates without leaving any residue
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Transparent Visual
Density at 20°C: 0.76 g/cm3 ASTM D 7042
Viscosity at 20°C: 1.8 mm2/s ASTM D 7042
Flash point: > 56 °C DIN EN ISO 2719
Copper corrosion: Not determined* DIN 51759-1
*Discolourations of non-ferrous metals should be examined in preliminary tests
Evaporating forming oil e.g. for coiling steel tubes for heat exchangers
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Yellow brown Visual
Density at 20°C: 0.84 g/cm3 ASTM D 7042
Viscosity at 20°C: 7.4 mm2/s ASTM D 7042
Flash point: > 61 °C DIN EN ISO 2719
Copper corrosion: Not determined* DIN 51759-1
*Discolourations of non-ferrous metals should be examined in preliminary tests
Drawing soap, for steel and galvanized steel, application at approximately 50°C
Physical Properties Typical Data
Parameter Typical results
Operating concentration 5 - 10 %
Operating temperature 75 - 90 °C
Retention time in soap bath 5 - 10 min
Drawing velocity Max. 100 m/min
Concentration (grease in piston) 6 - 7 % grease
Concentration (alkalinity in methanol) 0 - 2 ml
High performance oil for sawing tubes, Rattunde approval
Physical Properties Typical Data
Parameter Typical results Tested according to
Appearance: Medium brown, clear Visual
Density at 20°C: 0.91 g/cm3 ASTM D 7042
Viscosity at 40°C: 120.0 mm2/s ASTM D 7042
Flash point: > 180 °C DIN EN ISO 2719
Copper corrosion: Not determined* DIN 51759-1
*Discolourations of non-ferrous metals should be examined in preliminary tests

Testing media for leakage and ultrasonic tests

Fully synthetic product for ultrasonic tests, very good corrosion protection and ideal foaming behaviour
Physical Properties Typical Data
Concentrate
Colour Mineral oil content Viscosity at 20°C:
ASTM D 7042
Density at 20°C:
ASTM D 7042
Copper corrosion:
DIN 51759-1
Yellow Free 9.0 mm2/s 1.10 Not determined*
5% Solution
Colour pH-value
(tap water)
Corrosion protection
DIN 51360-2
Refractometer factor (brix) Conductivity
(Deionised water)
Transparent 9.4 5 % grade 0 1.9 2270 μS/cm
Characteristics
Mineral oil EP-additives Chlorine Boron Amines FAD
- - - + + +
*Discolourations of non-ferrous metals should be examined in preliminary tests
Fully synthetic product with very good material compatibility, water-miscible
Physical Properties Typical Data
Concentrate
Colour Mineral oil content Viscosity at 20°C:
ASTM D 7042
Density at 20°C:
ASTM D 7042
Copper corrosion:
DIN 51759-1
Yellow Free 4.7 mm2/s 1.05 Not determined*
5% Solution
Colour pH-value
(tap water)
Corrosion protection
DIN 51360-2
Refractometer factor (brix) Conductivity
(Deionised water)
Yellowish 9.6 5 % grade 0 2.2 Not determined
Characteristics
Mineral oil EP-additives Chlorine Boron Amines FAD
- - - + + +
*Discolourations of non-ferrous metals should be examined in preliminary tests