Solutions Products Support About Us Find a Distributor Contact Us
Solutions Products Support About Us
Solutions Products Support

New Products

TRIM® E730

Boron-free, Multi-metal Machining Emulsion

TRIM E730 is a boron-free, high quality, universal soluble oil which requires minimal maintenance in even the most demanding fluid management systems. It has broad application in machining and grinding on a wide range of materials. The high levels of both chemical and mechanical lubricity in this product handle the medium to high duty machining and grinding jobs. The stable and predictable performance of TRIM E730 makes it a first choice for high-quality, consistent parts manufacturing.

  • Very stable formula provides long operational life with consistent performance
  • Extremely hard water tolerant
  • Non-chlorinated and non-sulphurised extreme pressure (EP) additives control built-up edge (BUE)
  • Extremely fine soluble oil emulsion reduces carryoff for low total operating cost
  • Fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior corrosion prevention
  • Suitable for machining aluminium alloys, steel alloys, nickel alloys, cast iron and yellow metals
  • Easily recycled or disposed of without special handling or equipment
  • Will run effectively for long periods without the need for costly additives

WEDOLiT N 22-4

Prelube

WEDOLiT N 22-4 is a medium-viscosity, non-water-soluble forming oil for deep-drawing sheet steel, for example, for the automotive industry. This includes sheet metal that is galvanized, or hot-dip galvanized on one or both sides, sheet metal coated with zinc metal, aluminized sheet metal, or sheets made of aluminum or aluminum alloys.

The product meets the requirements of the test procedure according to VDA 230-213, and has been approved by all VDA members.

  • Also acts as an anti-corrosion oil
  • Subsequent preservation of drawn parts is not necessary due to the good corrosion protection
  • Can be applied by spraying, flooding, brushing or with felt rollers
  • The oil film can be easily removed with organic solvents or water-soluble alkaline cleaners

WEDOLiT FS 7400

Calibration Oil

WEDOLiT FS 7400 is a non-water-miscible, evaporating calibration oil for light to medium calibration processes.

  • Can be applied by dipping or spraying
  • The residues left on the surfaces after calibration evaporate completely during annealing

WEDOLiT AN 6999

High-Protection-Fluid 170°C flash point (aromatic content ≤ 2%)

WEDOLiT AN 6999 is a modern formulated corrosion inhibitor for steel and other metals. It offers long-term corrosion protection (indoor storage and potentially outdoor storage) and can be applied by brushes or by means of rollers.

  • Ideal for overseas transport
  • Suitable for VCI-foils
  • Good protection for outdoor storage
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Ideal for covered storage
  • Offers protection against atmospheric contamination, e.g. dissolved gases that cannot penetrate the protecting film (water vapour permeability)

WEDOLiT CN 3650-13

High performance cutting oil

WEDOLiT CN 3650-13 is a mineral oil based cutting oil for the manufacturing (especially deep-hole drilling) of steel and aluminium alloys. The product contains a combination of EP- and AW-additives, which increase the cutting performance significantly.

  • High performance product, which leads to an excellent surface finish and dimensional accuracy
  • Highly reduced oil mist formation
  • Reduces friction and wear and thus contributes to a high tool life
  • Offers high cooling properties with a very good wetting behaviour
  • Very good flushing behaviour with an optimal transport of chips and swarf
  • Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT CN 8250-2

Minimum quantity lubricant

WEDOLiT CN 8250-2 is a volatilizing high-performance lubricant, designed for use in all types of low and minimum quantity lubrication systems for milling, sawing, thread cutting and cold forming applications of non-ferrous metals

  • High pressure absorption capacity as well as excellent wetting and lubricating effect
  • No gumming and sticking
  • Reduces build-up of material on steels with a low carbon content
  • The excellent cooling and lubricating properties lead to a significant increase in service life of tools and to high dimensional accuracy of workpieces
  • Ensures extremely economical use
  • Can be easily and safely removed by spray, immersion and ultrasonic cleaning with neutral or alkaline industrial cleaners or with organic solvents

WEDOLiT CN 8471-36

High performance cutting and forming oil

WEDOLiT CN 8471-36 is an ester-based high-performance lubricant, suitable for all kinds of minimum quantity lubrication systems, e.g. for milling, sawing or thread forming, of steel, aluminium and non-ferrous metals.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Very good wetting ability and film formation without adhesion
  • The outstanding cooling- and lubrication properties lead to significantly reduced friction and wear and thus contribute to a high tool life
  • Leads to clean surfaces and contributes to achieve dimensional accuracy
  • Economical application
  • Very good oxidation stability
  • Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT CN 8570-25

Minimum quantity lubricant

WEDOLiT CN 8570-25 is a liquid, odour-less, water insoluble high-performance lubricant, suitable for all kinds of minimum quantity lubrication systems, e.g. for milling, sawing or thread forming, of steel, aluminium and non-ferrous metals.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Very good wetting ability and film formation without adhesion
  • The outstanding cooling- and lubrication properties lead to significantly reduced friction and wear and thus contribute to a high tool life
  • Leads to clean surfaces and contributes to achieve dimensional accuracy
  • Economical application
  • Almost no mist formation and residues
  • Very good oxidation stability
  • Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT EP 320 E

Expander oil, ester-based

WEDOLiT EP 320 E is a highly viscous, high-performance, ester-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

  • Very high film stability (even under high pressures)
  • Good adhesion properties on smooth surfaces, very good wear protection
  • Easily removable with water (spontaneous emulsification)
  • The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
  • The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 540 CM

Expander oil

WEDOLiT EP 540-CM is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

  • Very high film stability (even under high pressures)
  • Good adhesion properties on smooth surfaces, very good wear protection
  • Easily removable with water (spontaneous emulsification)
  • The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
  • The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 760

Expander oil

WEDOLiT EP 760 is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

  • Very high film stability (even under high pressures)
  • Good adhesion properties on smooth surfaces, very good wear protection
  • Easily removable with water (spontaneous emulsification)
  • The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
  • The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 760-CM

Expander oil

WEDOLiT EP 760-CM is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

  • Very high film stability (even under high pressures)
  • Good adhesion properties on smooth surfaces, very good wear protection
  • Easily removable with water (spontaneous emulsification)
  • The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
  • The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT FN 1170-225

High-performance forming oil

WEDOLiT FN 1170-225 is a medium viscous, chlorine containing forming oil for tube drawing and other cold forming operations of steel. The product offers also an excellent performance for precision cutting operations. The undiluted product is usually applied by spraying, brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieve dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 1450-850

Fully synthetic forming oil

WEDOLiT FN 1450-850 is a high viscous, water-insoluble lubricant for tube drawing and other cold forming operations of aluminium and non-ferrous metals. The undiluted product is usually applied by brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieve dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners
  • Evaporates at temperatures T ≥ 300°C without leaving any residues or stains on the metal surface. Therefore, no preliminary degreasing is necessary before a potential soft annealing

WEDOLiT FN 4455-25

Forming and stamping oil

WEDOLiT FN 4455-25 is a low viscous, water-insoluble lubricant for medium to heavy forming operations of steel and non-ferrous metals. A combination of EP additives offers a outstanding performance for precision cutting operations. The undiluted product is usually applied by spraying, dipping, brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieve dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 6870-440

High performance forming oil

WEDOLiT FN 6870-440 is a high-performance product, which is based on highly refined mineral oils. The product is suitable for heavy forming and machining operations of steel, stainless steel and aluminium (e.g. thread cutting, stamping or deep drawing).

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieve dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FW 7650

Water-miscible, fully synthetic coolant

WEDOLiT FW 7650 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

  • Due to its thermal stability the product can be used in the whole production line (forming, welding, calibration, sawing)
  • No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)
  • Can be centrifuged without loss of active substances
  • Removable with organic solvents or alkaline industrial cleaners
  • A bright workpiece surface is obtained after annealing

WEDOLiT FW 9114

Water-miscible drawing paste

WEDOLiT FW 9114 is a water miscible forming lubricant based on biodegradable natural raw materials. The product is universally applicable in steel forming processes.

The application concentration depends on the level of difficulty of the forming operations and has to be determined in preliminary tests. Concentrations of 10 - 30% are usually recommended.

  • Can be applied undiluted as a concentrate
  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Leads to clean surfaces and contributes to achieve dimensional accuracy
  • Very good material compatibility
  • Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT N 22-NV

Washing and forming oil

WEDOLiT N 22 NV is a thixotropic water insoluble washing oil for cleaning metal sheets and coils. The product is usually used in washing machines at ambient temperatures. Increasing the temperature to approx. 60 °C enhances the washing effect. The oil film that remains on the surface after the washing process offers sufficient forming properties for medium to heavy forming operations (for cold forming of uncoated and galvanized steel and for and aluminum).

Approved by Volkswagen (VW-Material-Nr. 29.4186) and by Mercedes Benz (Nr. 34/95-10576 VWT).

  • Compatible (according to tests and our experience) with all for the automotive industry typical adhesives and paints (KTL)
  • Acts as a corrosion protection agent. Therefore, a post-treatment of the drawn sheets is not necessary
  • An ageing stable film is formed after drawing
  • Can easily be removed with organic solvents or water soluble, mild industrial alkaline cleaning agents, even after long storage periods
  • A phosphating can easily be conducted after degreasing

WEDOLiT CW 6546

Water-miscible coolant

WEDOLiT CW 6506 is suitable for light to heavy cutting operations of steel, stainless steel, aluminium (e.g. sensitive aluminium alloys of the 2000 and 7000 series) and non-ferrous metals.

WEDOLiT CW 6506 is approved by CETIM according to specification EADS ASN 42302 annex 2, DASSAULT DQGT 0.4.2.0065 index D and by Bombardier BAMS 569-001 rev. B, for the aerospace industry.

  • Offers high cooling- and flushing properties with a very good wetting behaviour
  • Contributes to a high tool life
  • Very good application stability
  • Almost free of foam
  • Offers a very good skin compatibility

WEDOLiT FN 1430-115

Fully synthetic forming oil

WEDOLiT FN 1430-115 is a medium viscous, water-insoluble lubricant for tube drawing and other cold forming operations of non-ferrous metals. The undiluted product is usually applied by spraying, brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieve dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners
  • Evaporates at temperatures T ≥ 300°C without leaving any residues or stains on the metal surface, therefore, no preliminary degreasing is necessary before a potential soft annealing

WEDOLiT™ FN 1872-50

Reactive drawing oil

WEDOLiT FN 1872-50 is a water-insoluble, reactive drawing oil, based on special phosphoric acid esters, which creates an iron phosphate layer on iron and steel parts. The product is free of chlorine, sulphur or nitrites.

  • The product is used in a heated bath with a temperature of TBath = 60°C ± 5°C
  • After 10 - 15 min, a sufficient film should have been developed on the tube surface (residues of lime- or carbon deposits must be removed preliminary)
  • It is important to keep the water content in the product at a value of 1 - 1.7%, to form uniform phosphate layers on the tube surface
  • The product offers a short-term corrosion protection (max. a few days)
  • The pipes can be cleaned after drawing with alkaline cleaners, solvents or bright annealing

WEDOLiT FW 6550-165

Stamping and Forming Medium

WEDOLiT FW 6550-165 is a synthetic, mineral oil and chlorine-free, highly additivated punching and forming medium. The EP additives ensure a pressure-resistant lubricating film, even in difficult machining processes.

  • Suitable for deep-drawing, extrusion, punching and cutting processes not only on steels, but also on stainless steels
  • Undiluted by brush or felt roller and can be easily washed off with water
  • Does not contain any insoluble pigments such as graphite or molybdenum disulfide

WEDOLiT AN 7121

Lanolin-Protection-Fluid 100°C flash point
(aromatic content ≤ 2%)

WEDOLiT AN 7121 is a modern formulated corrosion inhibitor for steel and other metals, which develops a slightly greasy film. The resulting film consists of natural corrosion protection additives with a specific odour. It offers a long-term corrosion protection (indoor storage) and can be applied by spraying, flooding or rolling. Homogenisation before usage is recommended.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) or to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Ideal for VCI-foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Ideal for covered storage
  • Offers protection against atmospheric contamination, e.g. dissolved gases which cannot penetrate the protecting film (water vapour permeability)

WEDOLiT FN 6160-90

High performance forming oil

WEDOLiT FN 6160-90 is a water-insoluble, chlorinated lubricant for deep drawing and other cold forming operations, e.g. wire drawing, extrusion or thread forming of steel and stainless steel. The undiluted product is usually applied by flooding, spraying, brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieve dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 8830

Special forming oil

WEDOLiT FN 8830 is a chlorine free, pasty, water-insoluble lubricant for cold forming processes (e.g. pilgering) of high alloyed steels. The product is usually applied on the outer diameter by brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • The outstanding extreme-pressure properties combined with an exceptional adhesion offers the possibility for high degrees of deformation
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Contributes to achieving dimensional accuracy
  • Pigments will remain on the surface after annealing and need to be removed (e.g. by pickling with HCl or HNO3) before further processing

WEDOLiT AE 1030

High-Performance-Ester-Fluid

WEDOLiT AE 1030 is a dewatering fluid based on the latest ester technology that uses surface-active substances to displace both water and emulsions from the metal surface quickly. Even highly complex geometries can be efficiently dewatered. It is mainly used as an immersion bath at room temperature.

Not subject to the German solvent guideline VOC 31. BImSCHV or to the Swiss regulation concerning the incentive tax on volatile solvents (VOCV). Fulfils all requirements regarding ELV 2000/53/EG.

  • Due to its strong dewatering effect, residues of flushing water or water containing fluids such as emulsions or synthetic coolants are removed from the metal surface
  • Water/emulsions that enter the bath will settle on the bottom of the tank after a short period and can be drained off
  • Development of a clear phase boundary between the water and the product, without forming an emulsion phase
  • Excellent bath-life
  • Additive loss due to water contact: None

WEDOLiT AE 4313

High-Performance-Ester-Fluid

WEDOLiT AE 4313 is a modern formulated, ester-based corrosion inhibitor for steel and other metals, which offers protection for short overseas transports. It can be applied by spraying, flooding or by means of rollers.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Suitable for short overseas transport
  • No negative labelling
  • Suitable for VCI-foils
  • Stable against acidic and alkaline contamination
  • Excellent material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

WEDOLiT AN 6111

High-Protection-DW-Fluid 100°C flash point
(aromatic content ≤ 2%)

WEDOLiT AN 6111 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Ideal compatibility with VCI-foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Low

WEDOLiT AN 7210

High-Protection-DW-Fluid 130°C flash point
(aromatic content ≤2%)

WEDOLiT AN 7210 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Suitable for overseas transport
  • Ideal compatibility with VCI-foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Low

WEDOLiT AN 9921-100

Medium term RP 100°C flash point,

WEDOLiT AN 9921-100 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow bodies. It can also be applied by spraying, flooding or by means of rollers. Due to the high oil content, it can also be used as a straightening oil.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) or to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Can be used as a straightening oil or for light forming processes after the solvent has evaporated
  • Stable against acidic and alkaline contamination
  • Excellent bath life
  • Excellent material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Extremely low

WEDOLiT AS 2111

Universal RP 40°C flash point

WEDOiT AS 2111 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Extremely low

WEDOLiT AS 2111-CM

Protection-DW-Fluid 40°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS 2111-CM is a modern formulated corrosion inhibitor for steel and other metals, that offers protection for short overseas transport. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

  • Suitable for overseas transport
  • VCI films suitable: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed, especially before packing in boxes with film
  • Stable against acidic and alkaline impurities
  • Good material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Water displacing with very good wetting behaviour
  • Additive loss due to water contact: Extremely low

WEDOLiT CN 6850-26

High performance oil

WEDOLiT CN 6850-26 is a medium viscous high-performance oil for machining steel, stainless steel, cast iron, aluminium and non-ferrous metals. By using this oil, various processes can be avoided such as separate production lines for machining different materials and the preliminary cleaning of non-ferrous metals. The product can be applied undiluted by spraying, flooding or means of rollers.

  • High performance product, which leads to an excellent surface finish and dimensional accuracy
  • Highly reduced oil mist formation, almost no loss of evaporation
  • Reduces friction and wear and thus contributes to a high tool life
  • Offers high cooling properties with a very good wetting behaviour
  • Very good flushing behaviour for an optimal transport of chips and swarf
  • Easily removable with organic solvents or alkaline industrial cleaners
  • A higher or lower viscosity can be created (equal additive content) by variation of the base oil

WEDOLiT CS 8208

Water-miscible, fully synthetic coolant

WEDOLiT CS 8208 is suitable for ultrasonic testing systems. The product is also suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 5 - 10%). Not suitable for the manufacturing of workpieces made of zinc, aluminium and their alloys.

  • Offers high cooling- and flushing properties with a very good wetting behaviour
  • Contributes to a high tool life
  • Very good application stability
  • Almost free of foam
  • Offers a good skin compatibility
  • Due to its thermal stability, the product can be used in almost the whole process chain of welded tubes (forming, welding, calibration, sawing)

WEDOLiT FN 1190-2300

High-performance forming oil

WEDOLiT FN 1190-2300 is a highly viscous, chlorine containing forming oil for tube drawing and other cold forming operations of stainless steel. The undiluted product is usually applied by brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners
  • Soluble in chlorinated hydrocarbons

WEDOLiT FN 1571-2800

Drawing Brass and Copper Tubes

WEDOLiT FN 1571-2800 is a highly viscous, water-insoluble lubricant for tube drawing and other cold forming processes of aluminium and non-ferrous metals. The undiluted product is usually applied by brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners
  • Evaporates at temperatures T ≥ 300°C without leaving any residues or stains on the metal surface. Therefore, no preliminary degreasing is necessary before a potential soft annealing

WEDOLiT FN 2451-850

Fully synthetic forming oil

WEDOLiT FN 2451-850 is a highly viscous, water-insoluble lubricant for wire drawing and other cold forming processes, e.g. deep drawing, extrusion or thread forming, of steel, stainless steel and aluminium. The undiluted product is usually applied by brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 2551-1800

Fully synthetic forming oil

WEDOLiT FN 2551-1800 is a highly viscous, water-insoluble lubricant for wire drawing and other cold forming processes, e.g. deep drawing, extrusion or thread forming, of steel, stainless steel and aluminium. The undiluted product is usually applied by brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 4170-35

Chlorinated stamping oil

WEDOLiT FN 4170-35 is a low viscous, water-insoluble chlorinated lubricant for heavy forming operations of steel and stainless steel. A combination of EP additives offers an outstanding performance for precision cutting operations. The undiluted product is usually applied by spraying, dipping, brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 6870-38

High performance forming oil

WEDOLiT FN 6870-38 is a water-insoluble lubricant for wire drawing and other cold forming operations, e.g. deep drawing, extrusion or thread forming, of steel and stainless steel. The undiluted product is usually applied by flooding, spraying, brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 8850-90

Drawing small diameter tubes, diesel injection

WEDOLiT FN 8850-90 is a medium viscous, water-insoluble lubricant for tube drawing and other cold forming operations of steel. Due to the fact that the product also offers corrosion protection, no additional treatment is necessary (for short term storage). The undiluted product is usually applied by spraying, brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FS 4710

Solvent base for aluminum stamping 70°C

WEDOLiT FS 4710 is a low viscous, solvent-based lubricant for stamping and forming operations of steel, aluminium and non-ferrous metals. The undiluted product is usually applied by spraying, flooding, brushes or by means of rollers.

  • Good spreading behaviour, which leads to a uniform wetting of the metal surface
  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • If the product is finely dispersed, it evaporates after a short time without leaving any residue. Therefore, an additional cleaning step is not necessary. Otherwise, it is easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FS 6311

Evaporating forming oil

WEDOLiT FS 6311 is a low viscous, solvent-based lubricant for stamping and forming operations of steel, aluminium and non-ferrous metals, which also performs excellently in thread rolling operations (aluminium). The undiluted product is usually applied by spraying, flooding, brushes or by means of rollers.

  • Good spreading behaviour, which leads to a uniform wetting of the metal surface
  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • If the product is finely dispersed, it evaporates after a short time without leaving any residues. Therefore, an additional cleaning step is not necessary. Otherwise, it is easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FW 1960

Soap for tube drawing operations

WEDOLiT FW 1960 is a water-soluble alkaline soap for heavy drawing operations of steel tubes. The product is usually used as an immersion bath (bath temperature 75 – 90°C).

  • The product is designed to react with the zinc phosphate layer (which acts as lubricant) to form a zinc soap. The zinc phosphate layer should be at least 4 μm (at heavy forming operations, e.g. cold extrusion, up to 10 μm). Due to specific additives, a maximum conversion of zinc phosphate and the drawing media occurs, which results in an optimal performance regarding degree and rate of deformation
  • Can be used in very low concentrations of 5 - 10% as an aqueous solution (tube drawing). The best results are obtained with water free media
  • Offers (in combination with a zinc phosphate layer) very high cross-sectional reduction and high drawing velocities – up to 100 m/min (steel tubes with standard cross-sectional reduction)

WEDOLiT K 856

Dewatering, short term RP 100°C

WEDOLiT K 856 is a dewatering fluid with slight corrosion protection properties that uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can be dewatered efficiently. It is mainly used as an immersion bath at room temperature.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31 BImSchV) or to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Due to its strong dewatering effect, residues of flushing water or water containing fluids such as emulsions or synthetic coolants are removed from the metal surface
  • Water/emulsions that enter the bath will settle on the bottom of the tank after a short period and can be drained off
  • Development of a clear phase boundary between the water and the product, without forming an emulsion phase
  • Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
  • Excellent bath-life
  • Additive loss due to water contact: None

WEDOLiT AS 1211 (K 722)

Dewatering-fluid 40°C flashpoint
(aromatic content ≥ 2%)

WEDOLiT AS 1211 is a dewatering fluid with a corrosion protection that uses surface-active substances to displace both water and emulsions from the metal surface extremely quickly. Even highly complex geometries can be quickly and efficiently dewatered. It is mainly used as an immersion bath at room temperature.

The product is approved by Mercedes-Benz Group AG (formerly Daimler AG) (QSO 040212) under the name K 722.

  • Due to its strong dewatering effect, residues of flushing water or water containing fluids such as emulsions or synthetic coolants are removed from the metal surface
  • After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage
  • Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off
  • Development of a clear phase boundary between the water and the product, without forming an emulsion phase
  • Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
  • Excellent bath-life
  • Additive loss due to water contact: None