Solutions Products Support About Us Find a Distributor Contact Us
Solutions Products Support About Us
Solutions Products Support

New Products

TRIM™ TC 109

Silicone Free, Tank Side Defoamer

TRIM TC 109 is a silicone free antifoam or defoamer. It is used as a tank-side additive to control foam in water-miscible coolants, washing compounds, floor soaps, etc.

  • Antifoam
  • Silicone free

TRIM™ TC 108

Metalworking Fluid Defoamer

TRIM TC 108 is a highly effective tank side additive used to control foam in metalworking fluid systems.

  • Paintable
  • Plateable

TRIM™ SC310 nd

Microemulsion Semisynthetic - No Dye

TRIM™ SC310 nd is a no dye, high-oil, semichemical coolant. This product combines the cooling, rust inhibition, and wetting of a premium synthetic with the mechanical lubricity and machine "friendliness" of a soluble oil. SC310 nd is well-suited for general, high-speed machining and grinding of all materials.

  • Compatible with a very wide range of material including: cast iron, steels, copper, and many plastics and composites
  • Provides superior corrosion inhibition on all ferrous and nonferrous metals and eliminates “hot chip” and clinkering problems often seen when machining cast iron
  • Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance
  • Has exceptional sump life and very low makeup for extremely low total operating cost
  • Low odor and mist makes for an operator-friendly product
  • Extremely effective EP additive package
  • Contains no nitrites, heavy metals, phenolic compounds
  • Easy recycling or disposal with conventional techniques and equipment

TRIM™ DRIVE CF3

High-performance Fluid for Hard Disk Drives

TRIM DRIVE CF3 is a specialized, chlorine-free, heavy-duty coolant formulated to meet the high-precision machining and stringent chemical restrictions of the Hard Disk Drive (HDD) industry. It has very good wetting and great lubricity resulting in excellent surface finishes and its ease of wash-ability makes DRIVE CF3 an excellent choice for HDD components manufacturers. TRIM DRIVE CF3 will run in high-pressure situations with little to no foam.

  • In addition to aluminum alloy, it is also suitable for a wide range of materials including steels and stainless steels
  • Low foam even in high-pressure operations without the use of silicone antifoam
  • Good hydrodynamic lubrication to perform reaming and threading applications
  • Excellent anti-weld properties without the use of either chlorinated or sulfurized EP additives
  • Keeps machines very clean while leaving a fluid, oily residue for ease of cleaning and reduced machine maintenance costs
  • Does not require special disposal and is easily recycled
  • Non-staining on aluminum alloys commonly used to produce HDD components
  • After machining, parts can be washed easily and completely in aqueous washing systems

TRIM™ MicroSol™ 687NXT

Premium High-lube PRTR Microemulsion

TRIM MicroSol 687NXT is a translucent, premium high-lube, PRTR compliant microemulsion. The product is low foaming in soft water but is also stable in hard water. The product is designed to machine difficult to machine metals, such as stainless steel and Inconel. It is also good for most aluminum alloys including aerospace grade.

  • Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance
  • Excellent compatibility with a very wide range of material including stainless steel, nickel alloys, titanium, and aluminum alloys
  • Greatly extends useful life without the need for tank side biocides or fungicides
  • Low foaming for modern high-pressure, high-volume applications
  • Uses standard metalworking recycling and disposal techniques
  • Does not contain any chemical listed under Japan PRTR regulation
  • Provides superior corrosion inhibition on all ferrous metals

XYBEX™ ChipOut™

Chip & Sludge Remover

XYBEX™ ChipOut™

A perfect match-up with the PurifierPlus is the XYBEX ChipOut. It is also a compact, easy-to-use, affordable solution for optimizing production. It simply and effectively sucks out the coolant, chips, and swarf to collect and filter all solid impurities and return clean coolant to the tank.

Get the most from your coolant with ChipOut. It literally pays for itself in no time with significant cost savings.

    XYBEX ChipOut
    • Separates surface debris, bottom chips and swarf, and sediment from coolant
    • Extends coolant life
    • Improves surface finish on parts
    • Reduces maintenance
    • Uses diaphram pump air pressure, no electricity required
    • High suction power, flow rate of 180 liters/min
    • Runs during production without shutting off machine tools
    • Adjustable stainless steel filters: standard mesh 380 microns; optional: 830 microns and 180 microns
    • Optional floating device for maximum tramp oil collection
    • Portable and easy to use with multiple machines
    • Operates with water-soluble coolants or neet oils
    Cost effective ChipOut adds up to big savings
    • Reduces annual coolant cost
    • Reduces expensive parts rejects
    • Reduces maintenance to a minimum

XYBEX™ ChipOut Plus™

Magnetic Centrifugal Sludge & Chip Remover

XYBEX™ ChipOut Plus™

Looking for a fast, affordable way to have longer coolant life, reduce maintenance, and achieve better machinability and surface finish? Hardworking ChipOut Plus delivers all that and more in a compact, portable system that can hook up to machines throughout the shop.

It does double time, as both a centrifugal and magnetic separator for water-based cutting fluids or neat oils. It’s simple to use, powerful, and efficient.

First, the suction hose draws in the liquid and impurities. The filtration bucket traps large impurities before the sludge-containing fluid enters the centrifugal separator where fine particles are separated out by centrifugal force. The sludge then enters the powerful magnetic separator which efficiently removes magnetic metallic shavings and particles. Just like its name implies, it takes out chips - plus more!

    XYBEX ChipOut Plus
    • Separates surface debris, magnetic dust and shavings, chips, swarf, and sediment from coolant
    • Extends coolant life
    • Improves surface finish on parts
    • Reduces maintenance
    • Separates using centrifugal and magnetic force
    • Provides extremely fine filtration
    • No need to stop the machine
    • Quick filtration, easy to operate
    • Portable, use with multiple machines
    • No consumables needed
    Use hardworking, cost effective ChipOut Plus to reduce costs and build profits
    Save time and build up profits with ChipOut Plus.
    • Reduces annual coolant cost
    • Reduces maintenance and manpower
    • Reduces costly parts rejects

XYBEX™ PurifierPlus™

Cutting Fluid Purifying System

XYBEX™ PurifierPlus™

The portable, cost-effective XYBEX PurifierPlus system pays for itself with material cost savings, reduced downtime and recycling costs. Not only does it enhance production and make the workplace cleaner, it also is better for employee health and the environment.

Unlike units which simply separate machine tramp oil (the unwanted byproduct of the machining/metalworking process) from coolant, PurifierPlus has an ozone disinfection function which kills bacteria. Not only is the coolant cleaned and lasts longer, it’s purified and reused, and the subsequent problematic stench from bacteria and fungal growth is eliminated.

Improve production, reduce costs, and experience a cleaner workplace with PurifierPlus.

    XYBEX PurifierPlus
    • Separates free tramp oil and extends coolant life
    • Reduces tool wear and costly parts rejects
    • Easy to use with a handy set-timer to operate on its own
    • Adjustable flow rate filter from 10 to 30 liters/hr
    • Kills bacteria (for best results run 1 hour for each 100 liters in sump; ozone function disinfects at 500 mg/hr)
    • Built-in pH detector (optional) adjusts pH to control range
    • Portable for use on multiple machines in the facility
    PurifierPlus quickly pays for itself in savings
    • Saves 10% to 25% on annual coolant cost
    • Saves 30% to 50% on additional water cost
    • Saves 10% to 25% on tooling costs and part reworks
    • Reduces clean-up time 60% to 80% annually

TRIM™ E206KS

Long-life Emulsion

TRIM E206KS is a high quality universal emulsion coolant concentrate. It has been designed for a very broad range of metals allowing its effective use in most cutting and grinding operations, which requires minimal maintenance even in the most demanding fluid management systems. It has the lubricity and "guts" necessary to do heavy-duty machining. The stable and predictable performance of TRIM E206KS makes it a first choice for high-quality, consistent parts manufacturing.

  • Very stable formula provides long operational life with consistent performance
  • Has a very wide application range allowing its effective use on cutting and grinding
  • Extremely hard water tolerance
  • Extremely stable fine particle size emulsion to reduce carry-off and super-high penetrability to get the fluid to the point of cut
  • Provides good tool life and surface finishes
  • High tramp oil resistance for easy oil remove, longer coolant life and more opportunities to be recycled
  • Leaves a very light oily, non-gumming residue to prevent sticky ways, chucks, tool holders and fixtures
  • Coolant residue is easily removed with either water, working solution or aqueous cleaners
  • Good cleaning performance keeps machine tool very clean
  • Easy recycling or disposal with conventional techniques and equipment
  • Run effectively for long periods without the need for costly additives

TRIM™ E860KS bd

Premium, General-purpose Emulsion - Blue Dye

TRIM E860KS bd is a high quality, blue-dyed, general-purpose emulsion, which requires minimal maintenance in even the most demanding fluid management systems. It has broad application in machining and grinding on a wide range of materials. The high levels of both chemical and mechanical lubricity in this product handle the tough machining and grinding jobs. It leaves a very easy to clean protective film on the work piece and machine parts to prevent corrosion on metal surfaces including the machine tool. The stable and predictable performance of TRIM E860KS bd makes it a first choice for high quality, consistent parts manufacturing.

  • Very stable formula provides long operational life with consistent performance
  • Extremely hard water tolerant
  • Very wide application range
  • Suitable for both grinding and machining
  • Fine particle size emulsion reduces carry-off and facilitates getting the fluid to the point of cut
  • In high-speed turning and milling, provides good tool life and surface finishes
  • Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders, and fixtures
  • Coolant is easily removed with water, working solution or aqueous cleaners
  • Easy recycling or disposal with conventional techniques and equipment
  • Will run effectively for long periods without the need for costly additives
  • Works very well in general machining where traditional soluble oil may not cool sufficiently

TRIM™ HyperSol™ 888NXT

neo-synthetic precision aerospace machining fluid

TRIM™ HyperSol™ 888NXT

Experience ultimate versatility
HyperSol 888NXT's neo-synthetic technology masters the art of versatility. Providing exceptional performance on hard aerospace metals such as titanium and high-nickel alloys, stainless steels and Inconel®, it also offers the superior lubricity necessary for machining soft, gummy aluminum alloys. Delivering low foam, low odor and a long running lifespan while meeting the strictest environmental regulations, HyperSol 888NXT is redefining excellence in the coolant industry.
See your production soar to new heights with revolutionary TRIM HyperSol™ 888NXT!

U.S. Patent 11,396,708

  • exceptional performance on hard aerospace metals
  • superior lubricity for machining softer aluminum alloys
  • trouble-free production
  • safest, environmentally-friendly ingredients
  • long-running lifespan delivers high customer value
  • less scrap, low foam and low odor

TRIM™ C270WY

High-performance Synthetic

TRIM C270WY is a state-of-the-art synthetic coolant. C270WY provides excellent cooling and chip settling, good tramp oil rejection, and machine cleanliness. Meets the needs of the modern job shop for a single premium synthetic coolant for virtually all machining operations.

  • Compatible with a very wide range of materials including: cast iron, steels and copper alloys, as well as plastics and composites
  • Provides excellent corrosion inhibition on all common ferrous and nonferrous alloys
  • Does a great job in form grinding, drilling, tapping, and reaming operations without chlorine or sulfur-based EP additives
  • Extremely low carry-off for very low total operation costs
  • Very low foam and mist
  • Keeps your machines clean while leaving a soft, fluid film that protects the bare metal parts
  • The residual film is easily resoluble in coolant working solution to facilitate easy machine cleaning and minimize the buildup of sticky residues that can hold machine-destroying chips
  • Exceptional sump life and very good tramp oil rejection
  • A very low initial odor level which usually disappears after one to two days

TRIM™ C276

Clean-running Synthetic

TRIM™ C276

TRIM C276 is a synthetic coolant that meets the needs of the most modern and demanding manufacturers. C276 makes use of the latest synthetic coolant formulation and specially synthesized oil to produce a versatile product that is clean running, has great sump life, and is kind to both machines and operators. This product will perform well in centerless and cylindrical form grinding as well as on high-speed, single-point turning, and down-the-hole work on vertical and horizontal machining centers.

  • Very low foam and mist
  • Provides excellent corrosion inhibition on all common ferrous alloys
  • Keeps your machines clean while leaving a soft fluid film that protects the bare metal parts of your machine tools - this film is easily washed off with coolant working solution for easy machine cleaning
  • Excellent extreme pressure (EP) lubricity to do many form grinding, drilling, and tapping operations
  • Extremely low carryoff for very low total operation costs
  • Exceptional sump life and very good tramp oil rejection
  • Low initial charge odor which dissipates further after one or two days
  • Minimizes the buildup of sticky residues

TRIM™ C385

High-lubricity Honing Synthetic

TRIM C385 is a state-of-the-art synthetic coolant which provides excellent cooling and chip removal, good tramp oil rejection and machine cleanliness. C385 meets the need of the modern job shop for a single premium synthetic coolant for honing and virtually all machining operations.

  • Very low foam and mist
  • Great for form grinding, honing, boring, rolling, etc
  • Exceptional sump life and very good tramp oil rejection
  • Extremely low carry-off for very low total operating costs
  • Very low initial odor which usually disappears after 1-2 days
  • Compatible with dirty or grey cast iron cutting, grinding, and honing
  • Keeps your machines clean while leaving a soft, fluid film that protects the bare metal parts
  • The residual film is easily resoluble in the coolant working solution to facilitate easy machine cleaning and to minimize the buildup of sticky residues that can hold machine-destroying chips

TRIM™ E709FF

Long-life Emulsion

TRIM E709FF is a high quality universal emulsion coolant concentrate. It has been designed for a very broad range of metals allowing its effective use in most cutting and grinding operations, which requires minimal maintenance even in the most demanding fluid management systems. It has the lubricity and "guts" necessary to do heavy-duty machining. The stable and predictable performance of TRIM E709FF makes it a first choice for high-quality, consistent parts manufacturing.

  • Very stable formula provides long operational life with consistent performance
  • Has a very wide application range allowing its effective use on cutting and grinding
  • Extremely hard water tolerance
  • Extremely stable fine particle size emulsion to reduce carry-off and super-high penetrability to get the fluid to the point of cut
  • Provides good tool life and surface finishes
  • High tramp oil resistance for easy oil remove, longer coolant life and more opportunities to be recycled
  • Leaves a very light oily, non-gumming residue to prevent sticky ways, chucks, tool holders and fixtures
  • Coolant residue is easily removed with either water, working solution or aqueous cleaners
  • Good cleaning performance keeps machine tool very clean
  • Easy recycling or disposal with conventional techniques and equipment
  • Run effectively for long periods without the need for costly additives

TRIM™ E860KS

Premium, General-purpose Emulsion

TRIM E860KS is a high quality, general-purpose emulsion, which requires minimal maintenance in even the most demanding fluid management systems. It has broad application in machining and grinding on a wide range of materials. The high levels of both chemical and mechanical lubricity in this product handle the tough machining and grinding jobs. It leaves a very easy to clean protective film on the work piece and machine parts to prevent corrosion on metal surfaces including the machine tool. The stable and predictable performance of TRIM E860KS makes it a first choice for high quality, consistent parts manufacturing.

  • Very stable formula provides long operational life with consistent performance
  • Extremely hard water tolerant
  • Very wide application range
  • Suitable for both grinding and machining
  • Fine particle size emulsion reduces carry-off and facilitates getting the fluid to the point of cut
  • In high-speed turning and milling, provides good tool life and surface finishes
  • Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders, and fixtures
  • Coolant is easily removed with water, working solution or aqueous cleaners
  • Easy recycling or disposal with conventional techniques and equipment
  • Will run effectively for long periods without the need for costly additives
  • Works very well in general machining where traditional soluble oil may not cool sufficiently

TRIM™ MicroSol™ 692XT

Premium, High-lubricity, Low-foam Microemulsion

TRIM™ MicroSol™ 692XT

TRIM MicroSol 692XT is a high-lubricity, semisynthetic, microemulsion coolant. This formula delivers extended sump life, greater bio stability, and better foam control versus previous generation semisynthetic Microemulsions. It does very well in mixed metal situations and is compatible with a very wide range of materials including titanium, high nickel alloys, steels, copper, and aluminum alloys. Improved tramp oil rejection keeps your production running smoothly. Increase your profitability and production with TRIM MicroSol 692XT!

  • Improved lubricity for longer tool life
  • Dramatically extends useful life without the need for tank-side biocides or fungicides
  • Halogen free
  • Low foaming for todays demanding high-pressure, high-volume applications
  • Excellent alternative to chlorinated soluble oils on high-silica aluminum alloys
  • Provides superior corrosion inhibition on all ferrous and nonferrous metals
  • Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance
  • Requires no special disposal or recycling techniques

TRIM™ TAP HEAVY

High-lubricity Tapping Fluid

TRIM™ TAP HEAVY

TRIM TAP HEAVY is a 100% synthetic and vegetable-based lubricant possessing strong friction-reducing properties. Designed as a tough operation product for use with metals of low machinability, it's recommended for use at full-strength, brush-on use for reaming, tapping, and threading.

  • Especially for taps ½" diameter and larger
  • Contains no mineral oils
  • Promotes excellent finish
  • Ensures parts size control
  • Delivers exceptionally long tool life
  • Reduces rubbing of the tool flank
  • Water washable, for easy parts cleaning
  • Compatible with most TRIM fluids
  • Use for added lubricity on extremely tough jobs

TRIM™ TAP LIGHT

Tapping Fluid

TRIM™ TAP LIGHT

TRIM TAP LIGHT is a synthetic/vegetable/mineral oil blend possessing strong friction-reducing properties. Use with metals of low machinability; specifically recommended at full strength for flooding applications involving broaching, sawing, milling, tapping, threading, gear cutting and shaving, gundrilling, and reaming.

  • Especially for taps ¼" diameter and smaller
  • Promotes excellent finish
  • Ensures parts size control
  • Delivers exceptionally long tool life
  • Reduces rubbing of the tool flank
  • Water washable, for easy parts cleaning
  • Compatible with most TRIM fluids
  • Use for added lubricity on extremely tough jobs

TRIM™ E712

Low Maintenance, General Purpose Emulsion

TRIM™ E712 is high quality universal soluble oil which requires minimal maintenance in even the most demanding fluid management systems. It has broad application in machining and grinding on a wide range of materials. The high levels of both chemical and mechanical lubricity in this product handle the tough machining and grinding jobs. It leaves a very easy to clean protection film on the work piece and machine parts to prevent corrosion on metal surface including the machine tool. The stable and predictable performance of TRIM E712 makes it a first choice for high-quality, consistent parts manufacturing.

  • Very stable formula provides long operational life with consistent performance
  • Extremely hard water tolerant
  • Very wide application range. Suitable for both grinding and machining
  • Fine particle size emulsion reduces carry-off and facilitates getting the fluid to the point of cut
  • In high-speed turning and milling, provides good tool life and surface finishes
  • Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders and fixtures
  • Coolant is easily removed with water, working solution or aqueous cleaners
  • Easy recycling or disposal with conventional techniques and equipment
  • Will run effectively for long periods without the need for costly additives. Easily recyclable and/or dispose with conventional recycling and/or disposal techniques

WEDOLiT FN 2451-850

Fully synthetic forming oil

WEDOLiT FN 2451-850 is a highly viscous, water-insoluble lubricant for wire drawing and other cold forming processes, e.g. deep drawing, extrusion or thread forming, of steel, stainless steel, and aluminum. The undiluted product is usually applied by brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behavior
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behavior, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners

TRIM™ E860

Low-foam, High-lubricity Emulsion

TRIM E860 is a high-quality, general purpose emulsion for use on a broad range of ferrous and nonferrous metals, effective in most cutting and grinding operations. The stable and predictable performance of E860 makes it a first choice for precision and consistent parts manufacturing.

  • Very wide application range
  • Good hard water tolerance
  • Keeps machine tools clean
  • Works very well in general machining
  • Very stable formula provides good operational life with consistent performance
  • High tramp oil resistance for easy oil removal and longer coolant life
  • Easily recycled or disposed of using conventional techniques and equipment
  • Good balance of cooling and lubrication providing good tool life and surface finishes
  • Leaves a very light, oily, non-gumming residue to prevent sticky ways, chucks, tool holders, and fixtures
  • Extremely stable fine particle size emulsion allows for reduced carry-off and super-high penetrability to get the fluid to the point of cut