Login
Home

WEDOLiT AN 6723

Special-Fluid 100°C flash point
(aromatic content ≤ 2%)

WEDOLiT AN 6723 is a thixotropic corrosion protection oil for steel. It contains a combination of inhibitors which offers long-term protection for indoor storage and short-term protection for outdoor storage. It can be applied by spraying, flooding, brushing or rolling.
WEDOLiT AN 6723 fulfills all requirements regarding Altautorichtlinie 2000/53/EG. It is not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Ideal for overseas transport
  • Stable against acidic and alkaline impurities
  • Good material compatibility
  • The full corrosion protection develops, if the product is applied at temperatures of 50 - 60°C (for spraying: The temperature has to be adapted according to the specifications of the used device)
  • For an optimal protection of the treated parts, storage temperatures ≥ 36°C and a direct exposure to solar radiation should be avoided


WEDOLiT AN 7114

High-Protection-DW-Fluid 120°C flash point
(aromatic content ≤ 2%)

WEDOLiT AN-7114 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

WEDOLiT AN-7114 fulfills all requirements regarding Altautorichtlinie 2000/53/EG. It is not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Ideal compatibility with VCI-foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behaviour
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Low


WEDOLiT AN 9921-100

High-Protection-Calibration-Fluid 212°F flash point
(aromatic content ≤ 2%)

WEDOLiT AN 9921-100 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow bodies. It can also be applied by spraying, flooding, or by means of rollers. Due to the high oil content, it can also be used as a straightening oil.

Fulfills all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) or to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Can be used as a straightening oil or for light forming processes after the solvent has evaporated
  • Stable against acidic and alkaline contamination
  • Excellent bath life
  • Excellent material compatibility
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Extremely low


WEDOLiT AS 1012

Dewatering-fluid 40°C flashpoint
(aromatic content ≤ 2%)

WEDOLiT AS 1012 is a dewatering fluid with corrosion protection properties. It uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can efficiently be dewatered. It is mainly used as an immersion bath at room temperature.

  • Due to its strong dewatering effect, residues of flushing water or water containing fluids including emulsions or synthetic coolants are removed from the metal surface
  • After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage
  • Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off
  • Development of a clear phase boundary between the water and the product, without forming an emulsion phase
  • Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
  • Excellent bath-life
  • Additive loss due to water contact: None


WEDOLiT AS 1723

High-Protection-Waxdispersion-Fluid 30°C flash point
(aromatic content ≤ 2%)

WEDOLIiT AS 1723 is a universal, solvent-containing, long-term corrosion protection. It contains a newly formulated thixotropic wax dispersion, which allows a long period of protection under covered storage as well as a limited period of outdoor storage. It can be applied by spraying, flooding, brushing or by means of rollers.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • After the evaporation of the solvent (quick drying time), a waxy, light-coloured, non-adhesive and non-dust-binding, age-resistant protective film is formed on the treated surface
  • Good protection for outdoor storage
  • It´s recommended to homogenise the product before use or after a longer storage period
  • Protection against atmospheric contaminations such as dissolved gases that cannot penetrate the protective film (water vapour permeability)


WEDOLiT AS 2111

High-Protection-DW-Fluid 40°C flash point
(aromatic content ≤ 2%)

Documents
Read More...

WEDOiIT AS 2111 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behavior
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Extremely low


WEDOLiT AS 2251

High-Protection-DW-Fluid 40°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS-2251 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behavior
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Very low


WEDOLiT AS 2603

High-Protection-Waxdispersion-Fluid 40°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS 2603 is a universal, solvent-containing, long-term corrosion protection. It contains a newly formulated thixotropic wax dispersion, which allows a long period of protection under covered storage as well as a limited storage period for outdoor storage. It can be applied by spraying, flooding, brushing or rolling.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • After the evaporation of the solvent (quick drying time), a waxy, light-coloured, non-adhesive and non-dust-binding, age-resistant protective film is formed on the treated surface
  • Good protection for outdoor storage
  • It´s recommended to homogenise the product before use or after a longer storage period
  • Protection against atmospheric contaminations such as dissolved gases that cannot penetrate the protective film (water vapour permeability)


WEDOLiT AS 3040

Dewatering-fluid 60°C flashpoint
(aromatic content ≤ 2%)

WEDOLiT AS 3040 is a dewatering fluid with corrosion protection properties that uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can be efficiently dewatered. It is mainly used as an immersion bath at room temperature.

  • Due to its strong dewatering effect, residues of flushing water or water containing fluids including emulsions and synthetic coolants are removed from the metal surface
  • After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage
  • Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off
  • Development of a clear phase boundary between the water and the product, without forming an emulsion phase
  • Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
  • Excellent bath-life
  • Additive loss due to water contact: None


WEDOLiT AS 4111

Special-Fluid 60°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS 4111 is a leading edge universally applicable, corrosion protection which offers a long-term protection for indoor storage. It has been especially developed for loosening rusted parts and can be applied by spraying, flooding or via an immersion bath.

  • Suitable for overseas transport
  • Rust remover for humidity-related ignition problems in electrical systems
  • Loosens rusted screws, nuts, joints, hinges, switches and mechanisms
  • Cleans dirty tools and components and protects them from corrosion
  • Stable against acidic and alkaline impurities
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Water displacing with very good wetting behavior
  • Additive loss due to water contact: Low


WEDOLiT AS 4116

High-Protection-DW-Fluid 60°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS-4116 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing of rolling.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behavior
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Extremely low


WEDOLiT AS 4116-2

High-Protection-DW-Fluid 60°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS-4116-2 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behavior
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Extremely low


WEDOLiT AS 4116-3

High-Protection-DW-Fluid 60°C flash point
(aromatic content ≤ 2%)

WEDOLiT AS-4116-3 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

  • Ideal for overseas transport
  • Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
  • Stable against acidic and alkaline contamination
  • Good material compatibility
  • Water displacing with very good wetting behavior
  • Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
  • Additive loss due to water contact: Very low


WEDOLiT AW 8321 (K 110)

Water-miscible High-performance Fluid

WEDOLiT AW 8321 is universally applicable for parts cleaning and corrosion protection. The mineral oil free product is not only suitable for steel, but also for non-ferrous metals. Utilizing the latest technology, AW 8321 offers the possibility for a boron and formaldehyde free application.

  • The product forms a stable emulsion, regardless of the concentration. Due to the electrolyte and temperature stability, an application in heated baths is possible (recommended temperature 60 - 80°C)
  • Even at high temperatures the product is stable against contaminations (e.g. sodium sulfonates or phosphates)
  • Easily removable with solvents or alkaline industrial cleaners
  • For the corrosion protection it´s important that treated parts are completely dry before packaging. Dependent on the concentration a minimal to slightly noticeable film is formed on the metal surface
  • Very good compatibility with VCI foils
  • Outstanding material compatibility (even at higher concentration)


WEDOLiT CS 6206

Water soluble coolant

WEDOLiT CS 6206 is suitable for grinding of steel, cast iron, aluminum, non-ferrous metals, glass, and especially carbides.

  • Offers high cooling- and flushing properties with a very good wetting behavior
  • Contributes to a high tool life
  • Very good application stability
  • Almost free of foam
  • Offers a good skin compatibility


  • Recommended mixing ratio
  • Grinding:  from 4%
  • General cutting:  from 6%


WEDOLiT EP 1090-E

Expander oil

WEDOLiT EP 1090-E is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents the stick-slip- effect due to the high content of polar additives.

  • Very high film stability (even under high pressures)
  • Good adhesion properties on smooth surfaces, very good wear protection
  • Easily removable with water (spontaneous emulsification)
  • The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be easily separated into water and oily waste by the utilization of specific additives
  • The treated water can be reused for the preparation of a new emulsion (to a certain degree)


WEDOLiT EP 330 ES

Expander Oil

WEDOLiT EP 330 ES is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

  • Very high film stability (even under high pressures)
  • Good adhesion properties on smooth surfaces, very good wear protection
  • Easily removable with water (spontaneous emulsification)
  • The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be easily separated into water and oily waste by the utilization of specific additives
  • Due to the unique easy-splitting-technology, only a very small amount of the splitting media is needed
  • The treated water can be reused for the preparation of a new emulsion (to a certain degree)


WEDOLiT EP 435 E

Expander oil

WEDOLiT EP 435 E is a highly viscous, high-performance forming oil based on renewable raw materials. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

  • Very high film stability (even under high pressures)
  • Good adhesion properties on smooth surfaces, very good wear protection
  • Easily removable with water (spontaneous emulsification)
  • The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
  • The treated water can be reused for the preparation of a new emulsion (to a certain degree)


WEDOLiT EP 540 ES

Expander oil, Easy-splitting-technology

WEDOLiT EP 540 ES is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and due to the high content of polar additives, prevents the stick-slip-effect.

  • Very high film stability (even under high pressures)
  • Good adhesion properties on smooth surfaces, very good wear protection
  • Easily removable with water (spontaneous emulsification)
  • The emulsion can be used for pre- and post-cleaning of the pipes and expander heads and can be easily separated into water and oily waste by utilizing specific additives
  • Due to the unique easy-splitting-technology, only a very small amount of the splitting media is needed
  • The treated water can be reused for the preparation of a new emulsion (to a certain degree)


WEDOLiT EP 760 E

Expander oil

WEDOLiT EP 760 E is a highly viscous, high-performance forming oil based on renewable raw materials. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

  • Very high film stability (even under high pressures)
  • Good adhesion properties on smooth surfaces, very good wear protection
  • Easily removable with water (spontaneous emulsification)
  • The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
  • The treated water can be reused for the preparation of a new emulsion (to a certain degree)


WEDOLiT EP 760 ES

Expander Oil, Easy-splitting Technology

WEDOLiT EP 760-ES is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and due to the high content of polar additives, prevents the stick-slip-effect.

  • Very high film stability (even under high pressures)
  • Good adhesion properties on smooth surfaces, very good wear protection
  • Easily removable with water (spontaneous emulsification)
  • The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be easily separated into water and oily waste by utilizing specific additives
  • Due to the unique easy-splitting-technology, only a very small amount of the splitting media is needed
  • The treated water can be reused for the preparation of a new emulsion (to a certain degree)


WEDOLiT FN 1571-2800

Fully synthetic forming oil

Documents
Read More...

WEDOLiT FN 1571-2800 is a highly viscous, water-insoluble lubricant for tube drawing and other cold forming processes of aluminium and non-ferrous metals. The undiluted product is usually applied by brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieve dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners
  • Evaporates at temperatures T ≥ 300°C without leaving any residues or stains on the metal surface. Therefore, no preliminary degreasing is necessary before a potential soft annealing


WEDOLiT FN 4455-55

Forming-oil

WEDOLiT FN 4455-55 is a low viscous, water-insoluble lubricant for heavy forming operations of steel and non-ferrous metals. A combination of EP additives offers a outstanding performance for precision cutting operations. The undiluted product is usually applied by spraying, dipping, brushing, or rolling.

  • Stable load carrying capacity and a homogenous sliding behavior
  • Reduces friction and wear and thus contributes to a long tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behavior, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT FN 8850-90

Drawing oil

Documents
Read More...

WEDOLiT FN 8850-90 is a medium viscous, water-insoluble lubricant for tube drawing and other cold forming operations of steel. Due to the fact, that the product also offers a corrosion protection, no additional treatment is necessary (for short term storage). The undiluted product is usually applied by spraying, brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieve dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT FS 3310

Evaporating forming oil

WEDOLiT FS 3310 is a low viscous, water-insoluble lubricant for stamping and bending operations of steel, aluminium and non-ferrous metals. The undiluted product is usually applied by spraying, flooding, brushing, or rolling.

  • Good spreading behavior which leads to a uniform wetting of the metal surface
  • Stable load carrying capacity and a homogenous sliding behavior
  • Reduces friction and wear and thus contributes to a long tool life
  • Leads to clean surfaces and contributes to dimensional accuracy
  • If the product is finely dispersed, it evaporates after a short time without leaving any residues and therefore, an additional cleaning step is not necessary
  • It is easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT FS-4710

Evaporating forming oil

Documents
Read More...

WEDOLiT FS 4710 is a low viscous, solvent-based lubricant for stamping and forming operations of steel, aluminium and non-ferrous metals. The undiluted product is usually applied by spraying, flooding, brushes or by means of rollers.

  • Good spreading behaviour, which leads to a uniform wetting of the metal surface
  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a high tool life
  • Leads to clean surfaces and contributes to achieve dimensional accuracy
  • If the product is finely dispersed, it evaporates after a short time without leaving any residues. Therefore, an additional cleaning step is not necessary, Otherwise, it is easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT FW 3500

Water-miscible, fully synthetic coolant

WEDOLiT FW 3500 is a high-pressure agent for hydroforming-processes such as internal and external high pressure forming of steel plates, with different surface qualities and thicknesses. The product can also be applied in different grinding and cooling operations.

Approved by “FF Fluid Forming“

  • Offers very good high-pressure properties
  • Contributes to a high tool life
  • Very good application stability
  • Almost free of foam
  • Offers very good skin compatibility


  • Recommended mixing ratio
  • Hydrofroming:  from 5 - 10%
  • Grinding:  from 3 - 6%


WEDOLiT FW 7651

Water-miscible, fully synthetic coolant

WEDOLiT FW 7651 is suitable for the manufacturing of welded steel tubes. It fulfills the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

  • Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
  • No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)
  • Can be centrifuged without loss of active substances
  • Removable with organic solvents or alkaline industrial cleaners
  • A bright workpiece surface is obtained after annealing


  • Recommended mixing ratio
  • Tube welding:  from 4 - 6%


WEDOLiT FW 7840

Water-miscible, semisynthetic coolant

WEDOLiT FW 7840 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration from 7%).

The product is approved by Daimler Chrysler (QSO 040305) under the name WEDOLiT K 911.

  • Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
  • Can be centrifuged without loss of active substances
  • Removable with organic solvents or alkaline industrial cleaners
  • A bright workpiece surface is obtained after annealing


  • Recommended mixing ratio
  • Tube welding:  from 7%


WEDOLiT FW 9200 (C 66)

Water-miscible forming lubricant

WEDOLiT FW 9200 is an ester-based, water-miscible forming lubricant, which can be universally applied in forming (especially drawing) processes of brass and non-ferrous metals.

The application concentration depends on the level of difficulty of the forming operations and has to be determined in preliminary tests. Concentrations of 10 - 15% are usually recommended.

  • Can be applied undiluted as a concentrate
  • Stable load carrying capacity and a homogenous sliding behavior
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Very good material compatibility
  • Easily removable with organic solvents or alkaline industrial cleaners


  • Recommended mixing ratio
  • Drawing operations:  10 - 15%


WEDOLiT FW 9850

Anti spatter fluid

WEDOLiT FW 9850 is a water-miscible anti spatter fluid. The product is usually applied by spraying, but can also be applied with a brush or by means of rollers.

WEDOLiT FW 9850 is approved by Ford (Tox.-Nr. 115412, Mat.Nr. 1180012135), Renault SA (R 100092852), and Peugeot SA (Z 000204960) under the name V 793-357.

  • Delivered as a ready to use product
  • Free of pigments, silicones, and chlorine compounds
  • The film that remains on the surface reliably prevents welding beads from adhering to the surface and welding nozzles from becoming encrusted
  • Very good wetting ability
  • Easily removable with alkaline industrial cleaners (even after a longer storage period)


WEDOLIT K 856

Dewatering-fluid 100°C flashpoint
(aromatic content ≤ 2%)

Documents
Read More...

WEDOLiT K 856 is a dewatering fluid with slight corrosion protection properties that uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can efficiently be dewatered. It is mainly used as an immersion bath at room temperature.

Fulfills all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31 BImSchV) as well as to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

  • Due to its strong dewatering effect, residues of flushing water or water containing fluids such as emulsions or synthetic coolants are removed from the metal surface
  • Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off
  • Development of a clear phase boundary between the water and the product, without forming an emulsion phase
  • Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
  • Excellent bath-life
  • Additive loss due to water contact: None


WEDOLiT N 22-3

Special-Fluid (Prelube)

WEDLiT N 22-3 is a thixotropic, non water soluble, deep drawing agent, which was developed for cold forming of coated carbon steels. It is especially applicable for electro galvanized zinc-, zinc nickel coated-, and aluminized-sheets. Also good for aluminum and aluminum alloys. The product can be applied by spraying, flooding, or rolling.

Fulfills the requirements of all German automotive manufacturers according to VDA-213 and VW-A001, and has been approved by all VDA members.

  • Applications at ambient temperatures possible
  • A preheating of the oil to approximately 40 - 50°C is possible without the loss of the thixotropic effect after cooling
  • Acts at the same time as a corrosion protection agent, and therefore a post treatment of the drawn sheets is not necessary
  • An agent stable film is formed after drawing
  • Can be removed with organic solvents or water soluble, mild alkaline industrial cleaning agents, even after long storage periods
  • After grease removal, excellent phosphating is possible


WEDOLiT N 52

Universal forming and cutting oil

WEDOLiT N 52 is a mineral-oil based high-performance lubricant, suitable for all kinds of minimum quantity lubrication systems such as milling, sawing, or thread forming steel, aluminum, and non-ferrous metals*.
Approved by Rattunde & Co as a cutting oil for minimum quantity lubrication.

  • Stable load carrying capacity and a homogenous sliding behavior
  • Very good wetting ability and film formation without adhesion
  • The outstanding cooling and lubrication properties lead to significantly reduced friction and wear and thus contribute to a long tool life
  • Leads to clean surfaces and contributes to achieving dimensional accuracy
  • Economical application
  • Easily removable with organic solvents or alkaline industrial cleaners