Login
Home

Forming-en-US.png
Number of products for application is 19

WEDOLiT EP 1090 E

High performance expander oil

SDS
Documents
Read More...

WEDOLiT EP 1090 E is a high viscosity, highest performance, special oil, based on esters of natural origin. It is developed according to the highest technical standard for use in the pipe industry. The product has worldwide release of the expander head manufacturer SMS Meer and Fontijne Grotnes and is recommended by HAEUSLER, YSD, Mannesmann-Demag and Iprolam for the expander heads.

WEDOLIT EP 1090 E is used for lubrication of sliding surfaces and guideways mechanical expander under extremely high surface pressure in the manufacture of large diameter pipes made of steel, for example, for gas and oil pipelines. WEDOLIT EP 1090 E is used undiluted for the forming process. The product is self-emulsifying and can be removed by water. The emulsion can be used for pre- and postcleaning of the pipes and to clean the expander head.

  • Very high lubricating film stability under load
  • Good adhesion to smooth surfaces, good wear protection
  • Prevents stick-slip
  • Easily washable with water / emulsifies spontaneously
  • Stable emulsion but very easy to split


WEDOLiT EP 435 E

Expander oil

SDS
Data Sheet
Documents
Read More...

WEDOLiT EP 435 E is a highly viscous, high-performance forming oil based on renewable raw materials. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

  • Very high film stability (even under high pressures)
  • Good adhesion properties on smooth surfaces, very good wear protection
  • Easily removable with water (spontaneous emulsification)
  • The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
  • The treated water can be reused for the preparation of a new emulsion (to a certain degree)


WEDOLiT FN 1490-850

Fully Synthetic Forming Oil

SDS
Data Sheet
Documents
Read More...

WEDOLiT FN 1490-850 is a highly viscous, water-insoluble lubricant for tube drawing and other cold forming processes of aluminium and non-ferrous metals. The undiluted product is usually applied by brushes or by means of rollers.

  • Stable load carrying capacity and a homogenous sliding behavior
  • Reduces friction and wear and thus contributes to a long tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behavior, preventing stick-slip and chatter
  • Leads to clean surfaces and contributes to dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners
  • Evaporates at temperatures T ≥ 300°C without leaving any residue or stains on the metal surface and therefore, no preliminary degreasing is necessary before a potential soft annealing


WEDOLiT FN 2451-150

Semisynthetic forming oil

SDS
Data Sheet
Documents
Read More...

WEDOLiT FN 2451-150 is a medium viscous, water-insoluble lubricant for wire drawing and other cold forming processes, e.g. deep drawing, extrusion or thread forming, of steel, stainless steel and aluminum. The undiluted product is usually applied by brushes or rollers.

  • Stable load carrying capacity and a homogenous sliding behaviour
  • Reduces friction and wear and thus contributes to a long tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieve dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT FN 4455-55

Forming-oil

SDS
Data Sheet
Documents
Read More...

WEDOLiT FN 4455-55 is a low viscous, water-insoluble lubricant for heavy forming operations of steel and non-ferrous metals. A combination of EP additives offers a outstanding performance for precision cutting operations. The undiluted product is usually applied by spraying, dipping, brushing, or rolling.

  • Stable load carrying capacity and a homogenous sliding behavior
  • Reduces friction and wear and thus contributes to a long tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behavior, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT FN 6870-170

Conventional Forming Oil

SDS
Data Sheet
Documents
Read More...

WEDOLiT FN 6870-170 is a medium viscous, water-insoluble lubricant for deep drawing and other cold forming processes of steel (e.g. for auto bodies). Additionally, the product is suitable as a spot lubricant for thread cutting or blind hole drilling. The undiluted product is usually applied by spraying, dipping, brushes or by means of rollers.

The product meets the requirements of the test procedure according to VDA 230-213.

  • Stable load carrying capacity and a homogenous sliding behavior
  • Reduces friction and wear and thus contributes to a high tool life
  • Outstanding wetting ability and film formation without adhesion
  • Stable cold start behaviour, prevents stick-slip and chatter
  • Leads to clean surfaces and contributes to achieve dimensional accuracy
  • Easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT FN 8471

Forming Agent

SDS
Data Sheet
Documents
Read More...

WEDOLiT FN 8471 is a pigmented, pasty yet flowable, water-insoluble special lubricant for cold forging operations of ferritic and SiCromAl steels. FN 8471 can also be used for dry expansion, preferably as external lubricant, without additional cooling. The lubricant must be applied by hand over the incoming mandrel bar.

  • Does not contain any chlorine compounds and is based on a well-adhering, temperature-stable mineral oil
  • Special basic pigments are used for the consistency adjustment
  • The special granulation size of the pigments allows an almost wear-free surface despite the high load
  • The extremely high pressure stability combined with exceptionally good adhesion of the lubricant, even on smooth surfaces, allows processes with large cross-sectional reductions
  • When processing Sicromal steels, the lumps must be pre-heated to approx. 200-280°C when entering the pilger machine
  • Strong adhesion and the high temperature stability are of particular importance
  • Pigments which remain after the annealing on the surface need to be removed before further processing by pickling in HCl or HNO3


WEDOLiT FS 3310

Evaporating forming oil

SDS
Data Sheet
Documents
Read More...

WEDOLiT FS 3310 is a low viscous, water-insoluble lubricant for stamping and bending operations of steel, aluminium and non-ferrous metals. The undiluted product is usually applied by spraying, flooding, brushing, or rolling.

  • Good spreading behavior which leads to a uniform wetting of the metal surface
  • Stable load carrying capacity and a homogenous sliding behavior
  • Reduces friction and wear and thus contributes to a long tool life
  • Leads to clean surfaces and contributes to dimensional accuracy
  • If the product is finely dispersed, it evaporates after a short time without leaving any residues and therefore, an additional cleaning step is not necessary
  • It is easily removable with organic solvents or alkaline industrial cleaners


WEDOLiT FS 3710

Evaporating Drawing-oil

SDS
Data Sheet
Documents
Read More...

WEDOLiT FS 3710 is a non-water soluble, synthetic cooling lubricant of low viscosity. It is applicable for drawing- and punching-operations of aluminium. Can be applied undiluted by spraying, flooding, brushing or rolling.

  • Good wetting of the metal surface
  • Nearly odourless
  • Despite the good lubrication properties, the product is characterised by a quick evaporation and high flash point
  • The working area should be sufficiently ventilated, due to the amount of volatile hydrocarbons


WEDOLiT FS 3910

Straight Cutting and Bending Oil

SDS
Data Sheet
Documents
Read More...

WEDOLiT FS 3910 is non-water-soluble cooling lubricant with low viscosity for punching- and bending operations on steel and zinc coated steel. The product is not applicable for the treatment of nonferrous metals.

  • Can be applied undiluted by spraying, flooding, brushing or rolling
  • Has a good spread effect, which causes an optimal even wettability of metal surfaces
  • Has a simultaneously cleaning effect
  • Contains a combination of aromatic free solvents with additives of esters and extreme-pressure compounds and is therefore practically odorless
  • Is marked by a very fast evaporation with high flash point


WEDOLiT FW 3500

Water- soluble, fully synthetic Coolant

SDS
Documents
Read More...

WEDOLIT FW 3500 is a high-pressure agent for hydroforming-processes as there are IHU and AHU hydroforming of steel plates, with different surface qualities and thicknesses.

  • Very good high pressure properties
  • Very good foaming behaviour
  • Good demulsifying abilities
  • reliable corrosion protection
  • Good filtration abilities
  • "FF Fluidforming" approval


WEDOLiT FW 7651

Water-miscible, fully synthetic coolant

SDS
Documents
Read More...

WEDOLiT FW 7651 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 3 - 5%).

  • Due to its thermal stability the product can be used in the whole production line (forming, welding, calibration, sawing)
  • No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)
  • Can be centrifuged without loss of active substances
  • Removable with organic solvents or alkaline industrial cleaners
  • A bright workpiece surface is obtained after annealing


WEDOLiT FW 7652

Water miscible, fully synthetic coolant

SDS
Documents
Read More...

WEDOLiT FW 7652 is applicable for the manufacturing of steel tubes on tube welding machines, as well as press water additive. Furthermore it can also be used for zinc coated materials, whereat the formation of white corrosion is prevented.

  • Popular in use as a cooling lubricant in the manufacture of steel tubes on tube welding machines.
  • In a 5% aqueous solution, it fulfils the requirements for lubrication of the working rollers, cleanliness of the rollers and tubes, and corrosion protection for the tubes and the machine.
  • Based on the thermal stability, it can be used for cooling the electrode respectively the coil and impeder in high frequency welding, but also in the water cooling line for the weld seam.
  • The entire tube welding machine can thus be operated with a closed-circuit cooling system, requiring no intake of other water.
  • Removable with organic solvents or alkaline cleaners. Bright surface are preserved during heat treatment under inert gas.


WEDOLiT FW 7661

Water miscible, fully synthetic coolant

SDS
Documents
Read More...

WEDOLiT FW 7661 is popular in the manufacture of steel tubes on tube welding engines. With 3-5% aqueous solution, it fulfils the requirements for lubrication of the working rollers, cleanliness of the rollers and tubes and spend corrosion protection for the tubes and the machinery. Furthermore it can be used as additive in hydro-tester solutions to test the tubes on leak-tightness

With its thermal stability, it can be used not only for cooling of the electrode or the coil and impeder in high frequency welding, but also in the water cooling line for the weld seam. The entire tube welding machine can thus be operated with a closed-circuit cooling system, requiring no intake of other water.

  • Fulfil the requirements of the TRG 611
  • No emulsifying effect regarding mineral oils and engines lubricants.
  • Anticorrosion oil can thus be used on the Turk’s head of the tube welding engine in the manufacture of sectional tubing.
  • The cooling lubricant penetrating into the anti-corrosion oil separates from the oil residue after a relatively short settling time and without emulsifying.
  • Can be centrifuged out without loss of active substances.
  • Removable with organic solvents or alkaline cleaners.
  • The bright surface is preserved during a heat treatment under inert gas.


WEDOLiT FW 7840

Water-miscible, semi synthetic coolant

SDS
Documents
Read More...

WEDOLiT FW 7840 is suitable for light to medium cutting operations of steel, stainless steel and cast iron. Additionally, the product is suitable for the manufacturing of welded steel and galvanized steel tubes.

  • Offers high cooling- and flushing properties with a very good wetting behaviour
  • Contributes to a high tool life
  • Very good application stability
  • Almost free of foam
  • Offers a good skin compatibility
  • Due to its thermal stability the product can be used in the whole production line of welded tubes (forming, welding, calibration, sawing)


WEDOLiT FW 9200

Water soluble Coolant

SDS
Documents
Read More...

WEDOLiT FW 9200 is a water miscible high performance cooling lubricant with a high share of particularly efficient, polar lubricating additives based on natural fatty esters and fatty acids.

  • Boron free
  • Amine free
  • High lubrication performance
  • Good skin tolerance
  • WHC 1


WEDOLiT FW 9850

Anti-Spatter agent

SDS
Documents
Read More...

WEDOLiT FW 9850 is a spatter protection agent against welding beads on the basis of natural fatty substances and highly refined mineral oils.

WEDOLIT FW 9850 contains no insoluble pigments, and is free of silicones and chlorine compounds.

WEDOLIT FW 9850 will be delivered ready for use, thus an extensive and time-intense dilution is not necessary. It can be applied by spraying on the welding zone, but it can also be applied manually with brushes or rollers. The remaining emulsion-film on the surface reliably prevents the adherence of welding spatter on the sheet metal and incrustation of the welding-nozzles (systems MIG and TIG).

WEDOLiT FW 9850 contains rust prevention inhibitors, so that rust formation on the treated parts during drying of the emulsion is reliable prevented. Even after many weeks of storage of the treated parts, perfect degreasing by spraying or immersion with mildly or strongly alkaline cleaners is possible.

WEDOLiT FW 9850 has been approved under the name V 793-357 by
Renault (R100092852)
Peugot (Z000204960
Ford ( Tox Nr. 11 54 12 Mat-No. 11800 12135).



    WEDOLiT N 22-3

    Deep-drawing-agent

    SDS
    Documents
    Read More...

    WEDOLiT N 22-3 is a thixotropic, water insoluble, deep-drawing agent. Trough a combination of polar active substances with E.P.-(Extreme-Pressure) additives it is excellent suitable for non-cutting cold shaping of uncoated C-steels, zinc- and zinc/nickel-coated and aluminated sheet steel as for aluminium and aluminium alloys.

    WEDOLiT N 22-3 fulfills all requirements of all german automotive manufacturers according to VDA 230-213 and QPA VW-001, and has been approved by all VDA members.

    WEDOLiT N 22-3 can be applied by spraying or by hand with a brush or by means of rollers. A filtration over a fine-meshed filter (< 50 µ) is absolute to avoid, as the thickener will be filtered out. Heating the oil of approximately of 40-50°C before application is possible, without loss of the thixotropic effect after cooling.

    WEDOLiT N 22-3 acts at the same time as a corrosion protection agent. Represervation of the drawn sheet is not necessary. The film remaining on the component after drawing has good ageing stability and can be easily removed with organic solvents or water soluble, mild alkaline industrial cleaning agents, even after long storage of the components. After degreasing, phosphating treatment can be carried out without problems. WEDOLiT N 22-3 is free of insoluble pigments, such as graphite or molybdenum disulphide.



      WEDOLiT N 52

      Universal Forming and Cutting Oil

      SDS
      Data Sheet
      Documents
      Read More...

      WEDOLiT N 52 is a highly additivated forming- and cutting oil for deep drawing-, extrusion-, punching- and cutting-operations. The product is not only suitable for automotive- but also for ferritic- and high-strength chromium-nickel steel. It is applied undiluted by spraying, flooding, brushing, or rolling.

      Approved by Rattunde & Co as a cutting oil for minimum quantity lubrication.

      • Reduces friction and wear and thus contributes to a long tool life
      • Leads to clean surfaces and contributes to achieve a high dimensional accuracy
      • Offers an extremely pressure resistant film
      • Outstanding load carrying capacity
      • Easily removable with organic solvents or aqueous, alkaline industrial cleaners in a spray- or dipping-process